Lottes Roofing 1853 C Sherman Dr. St. Charles, MO 63303 We will work with you to give you the best deal on your EPDM, TPO, Modifed Bitumen, Roofing Shingles, Roof Coatings, Insulation and Roof accessory items!! Call or Email us TODAY!!! "Over 30 years experience in single ply flat roofing products!" Click Below for Certification, Qualification and Reference Data Click Here for Lottes Roofing Information 1-888-895-4465 These are 2 - 4 1/4 gal pails of Latex bonding adhesive 100 lbs and is Class C-60 FREE DELIVERY IN 48 states!! Please provide your shipping address, city, state and zip code Check out my other items! 200 page Specification & Installation guideline online manual available at Lottes Roofing Specs Page This is latex bonding adhesive to adhere the EPDM or TPO rubber to the roofing insulation or substrate. This is a latex based single surface bonding adhesive with coverage about 300-350 square feet on a SINGLE surface. This adhesive is a SINGLE surface laminate adhesive that is to be used in a WET condition. DO NOT ALLOW the adhesive to become dry before you lay in the roofing membrane. APPLY roofing menbrane while the adhesive is WET. So 2 - 4 1/4 gal pail will cover about 600-700 square feet of finished roof area. Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required. · 1 Clean the roof surface of all shingle debris and nails. Re-fasten any loose roof boards. · 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8" without risk of possible adhesion issues. · 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane · 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane. · 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3”seam tape if required to splice 2 pices of EPDM deck sheet together. · 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof. Seam tape application if required to join 2 sheets together •Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. •Clean and/or prime the seam area of both rubber sheets using FastSeam EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area •Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2" out from the edges of the bottom sheet. •Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. •With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. •Remove the paper backing by pulling out from under the top sheet at a 45?angle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. We have both WHITE TPO rubber and BLACK EPDM rubber roofing. INSTALLATION OF EPDM MEMBRANE RPU BONDING ADHESIVE The EPDM or TPO membrane may be installed in a fully adhered application directly over 1/2" or larger plywood decking, APPROVED DECKING OR APPROVED INSULATION, if the deck support is considered adequate for the roof load as determined by the local installer, and the roof installation meets local building codes. Position the EPDM or TPO membrane over the substrate, wood decking, concrete, or insulation, without stretching the sheet. Allow sufficient materials for perimeter attachment. When the new membrane is to be sealed to an abutting membrane, overlap the edge of the new membrane 5” onto the "in place" membrane. Bond the new sheet to the substrate by folding the sheet lengthwise on to itself so that one half of the underside is exposed. Smooth out all the wrinkles and buckles along the folded edge. Apply the bonding adhesive evenly at the rate of 70 -100 sq. ft. per gallon per receiving surface using a 9" plastic core paint core paint roller or application trowell with 1/8" x 1/8" groove indents. Apply the roofing menbrane onto the wet adhesive while still wet to insure "transfer" of adhesive to underside or roofing membrane. Roll or lay the membrane onto the substrate taking care to avoid wrinkling. Bond the adhered half of the membrane with a 18" to 24" heavy duty push broom using a pushing motion to achieve maximum contact. Pull back the unbonded half of the sheet and repeat this procedure. Do not apply adhesive to the top surface of any abutting membrane that is to be used as the seam joint. Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Money Orders, Bank Wire, Paypal Fees No sales taxes UNLESS in specific states locals Shipping US and International Delivery 24-48 hours to ship the liner NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me 1-888-895-4465 BID WITH CONFIDENCE Read my policies on my SquareTrade Seal stwithpolicies On Apr-28-08 at 11:12:31 PDT, seller added the following information:
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
