600A Clamp Multimeter,Thinner Jaws,Relative Zero Mode,Finger Guard,MeasuresAC&DC, US $91.83 – Picture 0

600A Clamp Multimeter,Thinner Jaws,Relative Zero Mode,Finger Guard,MeasuresAC&DC, US $91.83 – Picture 1

600A Clamp Multimeter,Thinner Jaws,Relative Zero Mode,Finger Guard,MeasuresAC&DC, US $91.83 – Picture 2

600A Clamp Multimeter,Thinner Jaws,Relative Zero Mode,Finger Guard,MeasuresAC&DC, US $91.83 – Picture 3

600a Clamp Multimeter,thinner Jaws,relative Zero Mode,finger Guard,measuresac&dc

US $91.83

Portland, Oregon, United States
Jan 29th

Open on mobile:
QR code

Amprobe 600A Clamp Multimeter Rubber over-molded case Hold and maximum reading functions Capacitance to 3000 uF Meets EN61010-2-032, UL61010B-2-032, IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed. CAT III-600 Volts ac & dc Pollution degree : 2 Digital clamp meter measures alternating current (AC) to 600 amp, direct current (DC) voltage and AC voltage to 600 volts (V), capacitance to 3,000 microfarads, resistance to 40 megaohms, and frequency to 100 kilohertz Average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform I ship to the lower 48 states only. I cannot combine shipping, and there is no local pickup. I cannot ship to PO Boxes or APO's AZB003Z7UQJA The Amprobe ACD-10 Plus digital clamp meter is an average-sensing, auto-ranging multimeter for measuring current, voltage, capacitance, resistance, and frequency in electrical testing applications. It has a transformer clamp that measures alternating current (AC) to 600 amp and frequency to 100 kilohertz (kHz), and it comes with detachable test leads that measure direct current (DC) voltage and AC voltage to 600 volts (V), capacitance to 3,000 microfarads, resistance to 40 megaohms, and frequency to 100 kHz. The clamp has two 0.4" (10 mm) thick jaws that are slimmer than standard clamp jaws for improved access to tight areas. The jaws can close around electrical conductors up to 1" (26 mm) in diameter to measure current without touching or interrupting the circuit. A relative zero mode stores a reading in memory to use as a zero point for subsequent readings, allowing for quick comparison of multiple readings. A finger guard on the body of the meter helps protect fingers from shock. It is an auto-ranging multimeter and automatically selects the correct operating range for the property being measured. Specifications Maximum alternating current (AC) input 600 amp Maximum AC voltage input 600 volts (V) Maximum direct current (DC) voltage input 600V Maximum resistance detected 40 megaohms Maximum capacitance detected 3,000 microfarads Maximum frequency detected 100 kilohertz (kHz) Power supply 3V IEC-CR2032 coin battery (one, installed) Standards met and certifications European Normal (EN); International Electrotechnical Commission (IEC) and EN safety standard 61010-1; European Conformity (CE); and Australia N10140 certified Weight 4.9 oz./139 g Meter dimensions 7.4 x 2.5 x 1.3 inches/190 x 63 x 32 mm (H x W x D) H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back. Clamp meters (also called clamp-on meters) measure electrical current without cutting through wires or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. Safety ratings are based on the International Electrotechnical Commission's (IEC) standards for low-voltage test equipment. What’s in the Box? ACD-10 Plus average-sensing digital clamp multimeter (1) Test lead set (1) 3V coin battery (installed) Soft vinyl carrying case Instructions