Amprobe Acdc-100 1000a Ac/dc Clamp Meter, New

US $139.06

Crosby, Texas, United States
Jan 29th

Open on mobile:
QR code

Amprobe ACDC-100 1000A AC/DC Clamp Meter Click Thumbnails to Enlarge The Amprobe ACDC-100 digital clamp meter is an average-sensing, auto- or manual-ranging multimeter for measuring current, voltage, capacitance, and resistance in electrical testing applications. It has a Hall effect clamp that measures alternating current (AC) to 800 amp and direct current (DC) to 1,000 amp. The meter comes with detachable test leads that measure DC voltage and AC voltage to 600 volts (V), capacitance to 3,000 microfarads, and resistance to 40 megaohms. The clamp has two jaws that can close around an electrical conductor up to 2" (50 mm) in diameter to measure current without touching or interrupting the circuit. The inrush reading displays measurement of entire motor inrush period at startup. A relative zero mode stores a reading in memory to use as a zero point for subsequent readings, allowing for quick comparison of multiple readings. The maximum reading mode displays the highest reading in a session to track a sudden increase in measurements. An audible continuity sensor confirms that the circuit conducts electricity, and a diode test detects whether a circuita??s diodes are working properly. The hold function keeps the reading on the display, even after the meter is disconnected. The backlit liquid crystal display (LCD) is visible in low light. The unit automatically turns off after 30 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. The meter has an impact- and wear-resistant molded rubber body with a probe holder. A finger guard on the body of the meter helps protect fingers from shock. This average-sensing, or average-responding, meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform. Two ranging modes (auto or manual) offer a range of operator control when taking readings. When turned on, the meter will be in auto-ranging mode and will automatically select the correct operating range for the property being measured. It can be switched to manual-ranging mode, which requires that the operator choose the appropriate operating range. The meter has a 4,000-count resolution, meaning it can display up to 3,999 units (3-3/4 digits) before the operating range needs to be changed. It meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V, which covers items used with enclosed building circuit installations (service panel parts, branch circuits, and fixed installations that are connected directly to a building's AC power supply). The unit comes with a soft vinyl carrying case with built-in probe storage. Specifications Maximum alternating current (AC) input 800 amp Maximum direct current (DC) input 1,000 amp Maximum AC voltage input 600 volts (V) Maximum DC voltage input 600V Maximum resistance detected 40 megaohms Maximum capacitance detected 3,000 microfarads Power supply 1.5V NEDA 24G, IEC R03, NEDA 24A, IEC LR03 AAA batteries (two, installed) Standards met and certifications European Normal (EN); International Electrotechnical Commission (IEC) and EN safety standard 61010-1; European Conformity (CE); Underwriters Laboratories (UL); and Australia N10140 Weight 0.6 lb./290 g Meter dimensions 1.6 x 3.1 x 1.6 inches/227 x 78 x 40 mm (H x W x D) H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back. Clamp meters (also called clamp-on meters) measure electrical current without cutting through wires or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. The meter's current clamp has two jaws that fit around a conductor to take measurements. All clamp meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltages determine meter choice. Safety ratings are based on the International Electrotechnical Commission's (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating. Amprobe manufactures electrical testing equipment for commercial, industrial, and home use. The company was founded in 1948 and is headquartered in Everett, WA. Whata??s in the Box?ACDC-100 average-sensing digital clamp multimeter Test lead set (2) 1.5V AAA batteries (installed) Vinyl carrying pouch with built-in probe storage Instructions Digital clamp meter measures alternating current (AC) to 800 amp, direct current (DC) to 1,000 amp, DC voltage and AC voltage to 600 volts (V), capacitance to 3,000 microfarads, and resistance to 40 megaohms Average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform Hall-effect current clamp with 2" (50 mm) jaw opening measures current without touching or interrupting the circuit Inrush reading displays measurement of entire motor inrush period at startup Meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V Shipping International Orders: Please allow an additional 3-5 business days handling time. We ship via the quickest, most economical method - usually UPS, FedEx, or USPS. We ship from multiple warehouses and will always ship from the closest warehouse to your location. We cannot guarantee ground shipping times, however most orders arrive in 3 business days once shipped. Payment Yozos gladly accepts PayPal, American Express, Discover, MasterCard, and Visa through eBay's safe and secure checkout. We do not accepts checks, cash, or any payments outside of PayPal. Returns Unused and uninstalled items may be returned within 30 days of purchase. Your return must be in new and unused condition. All returns must include original packaging, with all hardware and accessories. Orders returned outside of policy may be refused or subject to a 15% re-stock fee. Customers are responsible for return shipping costs. Damage claims must be made within 3 business days of delivery. After this time period, we cannot accept a damaged return. Damaged items will only be exchanged once we receive the damaged item back. For warranty questions please call 281-836-3229 or contact us through ebay. Contact Us FAQs HOW TO RETURN Contact us to obtain a Return Authorization number. Please include your return reason in detail. We will respond with a return authorization and return address, typically within 1 business day.

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Amprobe
Item Weight	1.5 pounds
Manufacturer Part Number	2740452
Product Dimensions	7.25 x 12.25 x 3.25 inches
Item Model Number	ACDC-100