APM 2.6 ArduPilot Flight Controller + GPS + 3DR 433 + Minimosd + Current Sensor APM 2.6 ArduPilot Flight Controller + GPS + 3DR 433 + Minimosd + Current Sensor APM2.6 and GPS Introduction: This is the new APM 2.6 autopilot module. The sensors are exactly the same as with APM2.5+, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers. The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors. This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself. Features: Arduino Compatible! Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer Onboard 4 MegaByte Dataflash chip for automatic datalogging Optional off-board GPS, uBlox NEO-6M module with Compass. One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000. Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties. Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively. 3DR Radio Telemetry Kit 433MHz: The 3DRobotics 3DR Radio is the ideal way to setup a telemetry connection between your APM and a ground station. Small, inexpensive and with great range, the 3DR radio uses an open source firmware which allows us to do things that cannot be done with other radios. Radio Features: Very small size Light weight (under 4 grams without antenna) Available in 900MHz or 433MHz variants Receiver sensitivity to -121 dBm Transmit power up to 20dBm (100mW) Transparent serial link Air data rates up to 250kbps Range of approx 1 mile MAVLink protocol framing and status reporting Frequency hopping spread spectrum (FHSS) Adaptive time division multiplexing (TDM) Support for LBT and AFA Configurable duty cycle Built in error correcting code (can correct up to 25% data bit errors) Demonstrated range of several kilometers with a small omni antenna Can be used with a bi-directional amplifier for even more range Open source firmware AT commands for radio configuration RT commands for remote radio configuration Adaptive flow control when used with APM Based on the HopeRF HM-TRP radio module, featuring an SiLabs Si1000 RF microcontroller. MAVLink-OSD V2.0 Introduction: MAVLink-OSD is an Arduino based project and it is fully compatible with original MinimOSD. This board can be used for CRIUS AIOP and Arduflyer / ArduPilot-Mega. MAVLink-OSD with switching DC/DC stepdown powersupply to maximize efficiency on power system. No more heating problems when using this OSD board. Default OSD Firmware is MinimOSD-Extra, written by Gabor Zoltan. Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable. The on-board switching regulator outputs 5.3V and a maximum of 3A from up to a 7S LiPo battery. Note: The Power Module is only designed to power APM/Arduflyer, a RC receiver and accessories (GPS, Radio telemetry). It is not designed to power servos. Use your aircraft's own ESC/BEC for that. Hardware Features: ATMEGA328P Microcontroller MAX7456-EUI monochrome on-screen display 5V/500mA DC/DC regulator for MAX7456-EUI Operating voltage: 5V(FTDI connector) and 12V(Video I/O connector) Supported NTSC & PAL FTDI connector Software Features: Full MAVLink protocol support Graphical configurator tool APM Arduflyer Power Module V1.0 Introduction: Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements,all through a 6P cable. The on-board switching regulator outputs 5.3V and a maximum of 3A from up to a 7S LiPo battery. Note: The Power Module is only designed to power APM/Arduflyer, a RC receiver and accessories (GPS, Radio telemetry). It is not designed to power servos. Use your aircraft's own ESC/BEC for that. Max input voltage: 30V Max current sensing: 90A Voltage and current measurement configured for 5V ADC Switching regulator outputs 5.3V and 3A max 6P molex cable plugs directly to APM/Arduflyer 2.5's 'PM' connector Specifications: Dimension: 25* 21* 9mm Weight: 17g (include all wire) Package Includes: 1* APM2.6 Board with case 1* Neo-6M GPS module with compass ic 1* MAVLink-OSD V2.0 1* Power Module 1* 3DR Radio Telemetry Kit 433MHz 1* Cables set 1.we only acceptA confirmed paypal A 2.please kindly payA withinA 3 days after youA bid A the product. A 3.please carefully check your EBayA address before you make the payment. A Item will be shipped within 2business days of cleared payment . Only shipped to buyer'sA ebay address, please confirm your address on ebay before you bid. Usually takes 7-20 business days to most Countries: US, Canada, UK, Australia and Europe. There are other ways of shipment like International Express Delivery DHL ,UPS, Fedex, EMS and TNT,extra shipping cost is needed. PleaseA contact us if you need this service. 1. You 'd better read our selling policy before buying from us. 2. We canA accept refund and replacementA if you receive wrongA item or damaged item and inform us within 2 weeks . 3.If you have any questions or problems with the item, please contact us through email 1. Our working time is from Monday to Saturday. So usually, we would reply emails within 24 hours. If you have any questions on the product you are interesting or your order , please contact us via eBay or email. We would be glad to help you. 2. During weekend, the reply would be delivered on next Monday. 3.We are not responsible for any custom duty or import tax. 1. Customer satisfactory is most important to us. If you have a problem or question regarding your transaction. 2. Please contact us before leaving negative or neutral feedback. If you choose not to contact, then the Feedback will be considered the final resolution and no further contact or email response will be provided. 3. If you have any problems,please kindly contact with us, we will try our best to help you.
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
