US $250.00
Condition | Used
:
An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
|
Seller Notes | “This is a used **American Made** precision grinding vise in very nice condition that has only minor surface staining in a couple of places. Other than that it is excellent.” |
Directions
Similar products from Grips & Tongs
Vintage Mini-Vise for Watch/Metalworking. C&E Marshall Co.
PANA-VICE with Suction/ Articulating Base with Circuit Board Clamps
VINTAGE SMALL MACHINIST VISE JIG FIXTURE
Vintage VomCleff & Co. New York Hand Vise Machinist Tool Made in Germany 1 5/8"
Moore jig borer Bay State precision vise 5-1/2" , 6" opening
Vintage Vulcan No. 2 Chain Pipe Vise by J.H. Williams & Co, Made in Brooklyn NY
Vintage 32 Lb. Wilton bullet machinist vise 3 1/2 "jaws excellent
THREE (3) L.S. STARRETT PIN VISES
PanaVise 318-22 22-Inch Crossbar for 315 324 And 333
MIT 4" Soft Jaw Vise Pads 4 inch Aluminum Rubber Permanent Magnet Michigan Tools
3 INCH HEAVY DUTY CROSS SLIDE VISE WITH METRIC DIAL (3900-2703)
CLEAN! SWIVEL BASE FOR 6" VISES - FITS KURT D60, D675, D688 VISES
Wilton Swivel Base Bench Mount Machinist Vise Heavy Duty Work Shop
Carbaloy TCL-10-3 5/8" x 5/8" x 4 3/8" Long Machinist
LARGE CHAS PARKER VICE WITH 6" JAWS. OPENS WIDE ,STANDS 40" TALL #107-USA
MAGNA-LOCK PERMA-CLAMPS MAGNA-GRIPS *FREE SHIPPING* machinist tools *9
THREE VINTAGE PARALLEL CLAMPS 2",3", RARE 5 INCH
People who viewed this item also vieved
Southwick & Meister TF25 Steel Collet .574"
Southwick & Meister TF25 Steel Collet .243"
Machinist ANGLE PLATE with Vee Block Built In, Tapped All Over, 3.75" H WL
Hardinge 7 In Face Plate, With Harding Taper Lock, Tool No. C-26
HARDINGE FACE PLATE C-27 9 INCH FACE PLATE T-SLOTS TAPPED HOLES
STANDARD CLAMPS CINCINNATI TOOL 2-1/2" NO. 640 C-CLAMPS (2)
C-CLAMPS HARGRAVE 6 & 4 NO. 41 (2)
C-CLAMPS WILLIAMS WILTON 404 CLAMPS (2)
8" Round Permanent Magnetic Chuck
SAMCHULLY MH-208 3-JAW 8'' HYDRAULIC CHUCK
12 pcs. pull studs M16 ISO 7388/II DIN 69872 form A
MT2 Live Center Morse Taper Triple Bearing Design Lathe Turning Revolving Thread
CONCENTRIC SPRING LOADED 3 MT/MORSE TAPER LIVE CENTER
LS Starrett No. S 154 L Set of 6 Adjustable Parallels in Pouch
Scissor table Westbend 9000 LB
JERGENS #10304 Solid Aluminum Handle 1/2-13 Thread Made in USA
V-BLOCK 3.5x2x1 7/8 toolmaker made read and look at pics
LATHE TOLLING BLOCKS TURRET LOC2209
LATHE TOLLING BLOCKS TURRET LOC2208
Haas Conversion Box for Rotary Table, Brush to Brushless. Model 32-0621.
Farmington 36" Air Bearing Pneumatic Rotary Table T Slot Powered
Young Bros. Young Bros 05092 9 Piece Hand Cut Stamp Figure Set, Steel, 3/16"
Young Bros. Young Bros 01362 36 Piece Hand Cut Stamp Combination Letter and
3 ER16 COLLET CHUCK EXTENSIONS w/ 1" SHANKS - #1"/RD16/140
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies