US $53.51
Condition: |
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details.
...
|
Manufacturer | MASTECH |
Model | MS2108A |
Directions
Similar products from Other Measuring & Monitoring Tools
STARRETT REPLACMENT VIAL,TUBE/PLUG FOR 98-8" LEVEL
M&H Inprocess Model #0841 Taper 50 Touch Probe, cat 50 made for Boeing Airlines
Starrett No. 57S Universal Surface Gauge Sleeve
Lot Metalworking Tooling Inspection Starrett scribe stand & others
Starrett No. S384JZ Set of Four Parallels in Case Machinists Parrallel set
ROCKWELL HARDNESS TESTER CYLINDRON JR ANVIL
Metallurgical Microscope Unitron MeC-5757 Pretty Nice!
MACHINIST LATHE MILL NICE 8" Machinist Level
F04974 UNI-T UT58C Standard Electrical Digital Multimeter Volt Amp Ohm Hz Temper
F04978 VICTOR VC9807A+ 4 1/2 Digital Multimeter Large LCD Screen AC DC Freq Test
F04983 VICTOR VC1010A Handheld Digital LuxMeter Photo Light Meter Lumens Test
F04984 UNI-T UT118B 3000 Counts AC/DC EF Function Pen Type Digital Multimeters
F04985 MASTECH MS6310 Handheld Combustible Methane Propane Gas Leak Detector
SPI - 13-145-8 - ELECTRONIC EDGE FINDER
Magnetic Particle Tester With Calibration Tool Nice!!!
F03908 VICTOR VC890C+ Digital DMM Multimeter Ohm Voltmeter Temperature Measureme
Starrett 653, Dial Indicator Comparator Stand, Fine Adjst., Height Gage
Thread measuring wires, .018-.185
People who viewed this item also vieved
Blue Point Digital Caliper U.S. Metric 0 - 6" (0-150mm) Snap-on MCAL6A
Mitutoyo Dial Bore Gage 511-170, 50-150mm, 0.001 graduation,
TELESCOPING GAGES, 6 PIECE SET, 5/16"-6", MADE IN KOREA, PLASTIC HOLDER, GOOD!
NEW MHC 6605-4070 DIAL INDICATOR 0-1 IN 0-100 INCHES
ACRA-MENT Dial Inspection Gage. 0” to .240” Travel. Used Good Condition.
MITUTOYO 2 ~ 3" .0001 Outside Micrometer Model #103-115 Machinist / Toolmaker
MITUTOYO 1~2" .0001 Outside Micrometer Model #103-114 Machinist / Toolmaker.
Starratt Manual CMM RCS 2828-18
Faro Laser Tracker Manual & Utilities Software V3.1.0
Starrett No. 154-C Adjustable Parallel
Machinist Toolmaker Starrett No. 299 Rule Clamp Pat. No. 2.194.085 Anthol, Mass.
10' X 7' X 18" Thick Gray Granite Surface Plate with Stand
T-Slotted Floor Plate Welding Table - 5' x 10' each, 18 avail, T-slot Floorplate
Magnet Brown & Sharpe Magnetic Block with On and Off Switch Machinists Tools
Starrett No. 657 magnetic base with Flex-O-Post w/ Hardinge 1" dial indicator
STARRETT # 20 MACHINIST 3" SQUARE
Mitutoyo 950-317 Digital Protractor
DXL360S Dual Axis Digital Angel Protractor 0.01° Resolution Rechargeable
2-3/8" x 2-3/8" Ultra Precision V-Block & Clamp Set in Fitted Box, #EG10-9012
10 Sets of 81-Pcs Steel Gage Block Set, Grade B, SAE, #P900-S581x10
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies