Fluke Networks 620 LAN CableMeter Cable Tester *FREE SHIPPING*, US $75.00 – Picture 0

Fluke Networks 620 LAN CableMeter Cable Tester *FREE SHIPPING*, US $75.00 – Picture 1

Fluke Networks 620 LAN CableMeter Cable Tester *FREE SHIPPING*, US $75.00 – Picture 2

Fluke Networks 620 LAN CableMeter Cable Tester *FREE SHIPPING*, US $75.00 – Picture 3

Fluke Networks 620 LAN CableMeter Cable Tester *FREE SHIPPING*, US $75.00 – Picture 4

Fluke Networks 620 LAN CableMeter Cable Tester *FREE SHIPPING*, US $75.00 – Picture 5

Fluke Networks 620 LAN CableMeter Cable Tester *FREE SHIPPING*, US $75.00 – Picture 6

Fluke Networks 620 Lan Cablemeter Cable Tester free Shipping

US $75.00

Oklahoma City, Oklahoma, United States
Jun 9th

Open on mobile:
QR code

Meter has been tested to power on only. This listing is for the meter only no other accessories are included. 620 LAN CableMeter® One person can verify each connection as he goes Test all LAN cable types - UTP, STP, FTP, Coax - Two, three, or four wire pairs in twisted pair cables - Test all category UTP cables and hardware Verify end-to-end connectivity per EIA/TIA 568 wiring standard Detects wiring problems: opens, shorts, miswires (crossed, reversed, split pair) Locates wiring/connection errors (distance to the open or short) Measures cable length Easy to use: Single rotary knob to select the test - Two line LCD display with backlight Handheld, long battery life (50 hours continuous) Test as you go The Fluke Networks 620 LAN CableMeter verifies the correct termination, connection and routing of LAN cabling. The 620 can test whether a connection has been properly implemented without using a remote unit at the other end of the cable. This allows the installers to “test the connection as they go.” Upon completing a connection, the installer can immediately verify that this connection is defect-free using a 620. No termination or connector is required at the other end of the cable. From one end, the 620 can detect (1) an open circuit and the length to this open (applies to each pair in a twisted pair LAN cable), (2) a short and the distance to this short circuit, (3) a split pair condition (the 620 shows the actual pairing detected). The installer saves time by diagnosing each connection right after completing that task. Installers don’t have to postpone testing until all connections have been made. And, if the cable plant requires “certification,” the final performance test on each cable channel will not be hampered or delayed by miswires, shorts, or opens. Wire termination errors can be identified as they occur and corrective action can be taken immediately without spending time in troubleshooting and fault isolation at cable plant “certification” time. Verify cable routing An installer can attach a “cable identifier” (optional) to a completed LAN connection to verify the cable routing and label, plus detect miswire possibilities such as reversed or crossed pairs in twisted pair cables. Measurement capabilities The following table summarizes the fault detection and fault location capabilities of the 620 LAN CableMeter without using a remote unit – called cable identifier – and with the cable identifier. Operation The 620 utilizes a two line LCD display (16 characters each). The display is equipped with a backlight to provide easy reading under all ambient light conditions. The Fluke Networks 620 implements three cable connectors: an RJ45 socket for UTP or FTP cable, a DB9 socket for IBM Type #1 STP cable, and a BNC connector for coax. The instrument is powered by two AA size 1.5 volt alkaline batteries. The battery life is 50 hours, not including the consumption of the backlight. A Setup button provides the ability to select the cable type, wiring standard (e.g. 10Base-T, 2 pair), cable category and wire gauge of the cable to be tested. In addition, the setup menu allows the user to: Enable or disable the audible pass/fail sound. Adjust the display contrast. Calibrate the meter to a specific type of cable. Select the language on the display (English, French, German, Italian, Japanese, Spanish). Select the units for length reports (feet or meters). The rotary selection switch offers three modes of operation: 1. Test provides a pass/fail report on the cable under test. In case a failure has been detected, the display offers additional diagnostic information. 2. Length provides the length of each pair (in case a twisted pair cable is being tested). 3. Wire Map provides the detail wiring for the cable. Specifications Length Range 1 to 999 ft or .5 to 300m Resolution 1 ft or .5m Accuracy 5% ± 3 ft or 5% ± 1m Display Feet or meters Power Two AA size 1.5 volt alkaline batteries Battery life: 50 hours of continuous operation, not including backlight consumption Input protection The inputs withstand telephone ringing and loop voltages. The instrument warns the user with an “Active Cable” message and an audible warning tone. Size 7.25 in x 3.87 in x 1.8 in (18 cm x 9.8 cm x 4.6 cm) Weight 12.5 oz (354g) The one-person LAN cable verification tool

“In great condition.”

Brand	Fluke Networks
MPN	Does Not Apply
Model	620 CableMeter
Country/Region of Manufacture	United States
Connectors	RJ-11, RJ-45, Ethernet Cat 5
UPC	095969024280

Fluke Networks 620 Lan Cablemeter Cable Tester *free Shipping*

Fluke Networks 620 Lan Cablemeter Cable Tester free Shipping