This is a used item that starts up. Have not printed with it. Item looks to be complete with no manual. Graphic languages The printer accepts drawing data from CAD and other software programs supporting the following languages: Hewlett-Packard Graphics Language (HP-GL), a vector language HP-GL/2, an enhanced version of HP-GL HP-RTL PJL PostScript (R) (HP Designjet 650/PS, or 650C printers with PostScript installed) top HP Designjet 650C Printer Model A Expandable top and bottom margins from 17 mm to 10 mm 300 x 300 dpi for Final and Draft modes Able to accept ROM SIMMs Sheet and roll media support Automatic cutter when plotting with roll media Hot I/O switching top HP Designjet 650C Printer Model B User selectable and faster drying times Automatic Language Switching New scatter halftone dither PANTONE (R)* Support Novell Certified Recommended cables RS-232-C interface The use of a short cables (each less than 15 meters or 50 feet) is recommended for the RS-232-C interface. A longer cable is permissible, provided the load capacitance does not exceed 2500 picofarads. Centronics interface The use of a short cable of 10 feet (3.5 m) or less is recommended for the Centronics interface. Media specifications Media sizes Width (carriage axis) Length (paper axis) E/A0-size printer D/A-1 size printer Minimum 210 mm (8.3 inches) 210 mm (8.3 inches) Maximum 917 mm (36.1 inches) 625 mm (24.6 inches) Minimum 280 mm (11 inches) 280 mm (11 inches) Maximum 1297 mm (51 inches) 1297 mm (51 inches) Media types Monochrome Plain paper bond Plain vellum (HP preferred) Plain translucent paper (HP preferred) Hewlett-Packard polyester Inkjet film HP special Inkjet paper Color HP special Inkjet paper Margins Leading edge: Trailing edge: Sides: Normal 17 mm (0.67 inches) 17 mm (0.67 inches) 5.0 mm (0.2 inches) Expanded (roll media only) 10 mm (0.39 inches) 10 mm (0.39 inches) 5.0 mm (0.2 inches) All measurements +/- 2 mm (0.08 inch) Resolution Mono Color Final and Draft modes: 300 x 300 dpi Enhanced mode: 600 x 600 dpi PostScript mode: 300 x 300 300 x 300 dpi Accuracy (Maximum accumulated error) +/-0.38 mm (0.015 inches) or +/-0.2% of the specified vector length, whichever is greater, at 23 degrees C (73 degrees F), 50–60% relative humidity, on HP Matte Film in Mono mode. Media handling The printers handle media that does not exceed the following maximum and minimum: E-size D-size Min. width Sheet 8.3 inches (210 mm) A/A4-E/A0 8.3 inches (210 mm) A/A4-D/A1 Roll widths Max. widths 24 inches AND 36 inches 36.1 inches(917 mm) 24 inches 24.6 (625 mm) Max. Sheet length expected to be 1.6 m Long axis plotting available [maximum length 50 feet (15.2m) and 9 feet with PostScript driver]. The media margins define the real available plotting area on the media NOTE: Long axis plotting may require a special driver or PPD file. Ink information Black Inkjet print cartridge 51640A Pigmented ink dark black ink crisp sharp characters fast dry time optimized to prevent black to color bleed Permanence lightfastness water resistance highlighter type smear or blurred text optimized to prevent black to color bleed Color Inkjet print cartridge 51650(C) (M) (Y) Color Cartridges OR 51640A for black Dye-based. High quality color CAD output on plain bond paper with a lower cost per page. Designed specifically for use with HP special Inkjet paper. Memory information The HP Designjet 650C printer has 4 megabytes (MB) of standard on-board RAM. A PostScript ROM SIMM and MIO card are optional. There are two RAM expansion slots which can hold optional 2 MB, 4 MB, 8 MB, 16 MB or 32 MB single in-line memory modules (SIMMs). The maximum expandable RAM is 64 MB additional, or a total of 68 MB. (Before the introduction of the Model B printer and the 16 and 32 MB SIMMs, maximum expandable memory for the Model A printer was 20 MB as specified in the User's Guide .) The HP Designjet 650C/PS printer comes pre-installed with 4 MB of standard on board RAM, a PostScript ROM SIMM and Jetdirect MIO card and requires a minimum of 4 MB additional memory or a total of 8 MB. Performance "Normal" printer use "Normal" printer use means less than: 40 pages per day (if medium-density E/A0 CAD plots), or 10 pages per day (if medium-density E/A0 image prints) The reliability of the HP Designjet 650C printer will be maximized by maintaining an output volume within 40 EA0-size plots per day on average. The HP Designjet 650C printer can support the occasional need for up to 100 plots per day, but the regular use of the HP Designjet 650C printer above an average of 40 plots per day may result in increased maintenance requirements. Producing more than 40 E/A0-size plots per day and/or changing the most frequently used pen cartridge (generally the black) more than once every 3.5 days, is working the HP Designjet 650C printer at above average conditions which will result in increased maintenance requirements. A plot counter is contained in the EEROM of the printer, the contents of which can be seen by performing a Configuration Plot from the front panel. For all 'A' models and 'B' models below firmware rev. 5.11 the plot counter only reflects non-PostScript plots. For 'B' models starting with firmware rev. 5.11, both PostScript and non-PostScript files are counted. The value is listed in hexidecimal format on line 0 of the EEROM map at the bottom of the Configuration plot, in columns c, d, and e. The count is displayed in reverse order and must be reversed when determining the number of plots. To print the configuration plot Make sure media is loaded. In the Full Menu mode, choose Utilities . Choose Config Plot option and press ENTER. Physical specifications Weight Length Width Height D-size 07.6 kg (128 lb) 1079 mm (54.0 inches) 711 mm (28.0 inches) 1149 mm (45.25 inches) E-size 69.75 kg (155 lb) 1371 mm (42.2 inches) 711 mm (28.0 inches) 1200 mm (47.25 inches) D-size, body only (shipping weight) 50.0 kg (110.2 lb) E-size, body only (shipping weight) 60.0 kg (132.2 lb) D-size, legs and bin (shipping weight) 21.0 kg (46.3 lb) E-size, legs and bin (shipping weight) 26.0 kg (57.3 lb) Electrical specifications Source 100–240V AC +/-10%. Frequency 47 - 63 Hz Power consumption 140 W (2.0 A max.) Environmental specifications Operational Mechanical and electrical: 0 to 55 degrees C (32 to 131 degrees F) @ 20-80% relative humidity With cartridges and media: 15 to 35 degrees C (59 to 95 degrees F) @ 20–80% relative humidity For optimal print quality and media handling: 15 to 30 degrees C (59 to 86 degrees F) @ 20–80% relative humidity Storage Printer and media –40 to 70 degrees C (–40 to 158 degrees F) @ 5-95% relative humidity Cartridges - black Cartridges - color –40 to 60 degrees C (–40 to 104 degrees F) –40 to 70 degrees C (–40 to 158 degrees F) Processor Intel 80960, 32-bit RISC
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
