US $400.00
| Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Manufacturer | Kitagawa |
| Model | B-206 | ||
| Country/Region of Manufacture | Japan |
Directions
Similar products from Lathe Chucks
84943679 Set (3) Serrated Soft Jaws- F/10" Kita Chuck Howa
Round Machinable Chuck Jaws HC12-41 Performance Jaws 5-1/2" x 3"
THREE JAW 10" CHUCK D-1-6 DIRECT MOUNT
BTC 8" 3 JAW LATHE CHUCK D1-4 MOUNT
Lathe 6" 4-Jaw ChuckMade by Skinner Chuck Co. No.906
8''/200mm 4-Jaw Independent Lathe Chuck, Plain Back, #0557-0008
D1-3 Type Adaptor, Chuck Diameter = 5", Spindle Taper = D1-3, #2600-0517
3"/75 mm 3-Jaw Lathe Chuck, Plain Back x0.003" TIR w/ 2 Sets of Jaws, #0559-0110
5 / 16 GEOMETRIC LATHE CHUCK 4 JAW
3 Jaw 3 Inch Chuck with Key and 3 Screws
D1-5 Camlock Face Plate 12" T-Slot
Hardinge 5C HV vertical and horizontal
ENGLAND! CRAFTSMAN 4" INDEPENDENT FOUR-JAW LATHE CHUCK w/ 3/4" x 16 TPI MOUNT
1 USED 72'' DIAMETER HEAVY DUTY 4 JAW CHUCK
Vintage JACOBS Drill Chuck MFG. CO. # 36 Chuck Key 3" Tapered Shaft 3/4"
BROWN & SHARPE 9" ROUND PERMANENT MAGNETIC CHUCK MODEL 9-R
BROWN & SHARPE NO. 5R 5" ROUND MAGNETIC CHUCK
People who viewed this item also vieved
6 3/8" SINE BAR / PLATE machinist tools 6 3/8 x 3/4 inches x 1 5/8 " Hardened
6 inch mount plate for LATHE CHUCK 2 1/4 8 tpi. was on Logan lathe
RIDGID ANGLE PIPE WELDING VISE 462 1/2" - 12" Chain Vise Fitter Welder Jig 40225
Bison 6MT Super Precision Triple Bearing Live Center 7700 lb. Capacity 7-565-106
Enco Live Center Lathe Tailstock Morse Taper #3 3MT France live center spindle
USED #6MT LATHE DEAD CENTER (POINT DIA. 2.50")
DE-STA-CO 227-U Horizontal Hold-Down Toggle Locking Clamp with U-Shaped Bar
Te-Co 20608 38 Piece T-Nut and Stud Kit 5/8"-11 Stud x 11/16" Table T-Slot
2 STARRETT # 161-B TOOLMAKERS' PARALLEL CLAMPS 1 3/4" CAPISITY 2 1/2" LONG JAWS
7" X 3" TOOLMAKER GRINDING HARDENED STEEL SCREWLESS VISE USED
Vintage Columbian USA D43-1/2 vise vice good working condition 3.5"
The Ridge Tool Elyria Ohio.USA.Vintage Pipe Vise B-Y-1 1/4
"Kaisercraft Dies-Beautiful, Cherish, Special To 1.5""X4.25"
"CandiBean Cling Stamp 4""X7""-Horsing Around"
Nandog My BFF Unstuffed 10 Squeakers Plush Toy-Grey Raccoon
(LOT OF 2) LUFKIN NO. 905 V-BLOCK With Clamps
MACHINIST TOOL LATHE MILL Machinist Lot of Ground Toolmakers Angle Block s
MACHINIST TOOLS LATHE MILL Machinist 2 1 2 3 Block s for Set Up
Rotary Table Horizontal & Vertical 3" / 75mm with 65mm Lathe Chuck for Milling
NEW TILTING ROTARY TABLE 4" / 100MM FOR MILLING MACHINES - QUALITY TABLE
Rotary Table Horizontal & Vertical 3"/75mm + 3 Jaw 65mm Lathe Chuck for Milling
FEDERAL STAND MODEL 100B-20 (# 1015)
Cylindrical Cleco Runner with 1/4" and 3/8" drives
SIGNATONE MODEL S-725-CRM MICROPOSITIONER
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies