LOOP DETECTOR;DETECTOR TESTER-MINI SIZE.&.GREAT FOR INSTALL TEST & COMMISSIONING, US $15.00 – Picture 0

LOOP DETECTOR;DETECTOR TESTER-MINI SIZE.&.GREAT FOR INSTALL TEST & COMMISSIONING, US $15.00 – Picture 1

LOOP DETECTOR;DETECTOR TESTER-MINI SIZE.&.GREAT FOR INSTALL TEST & COMMISSIONING, US $15.00 – Picture 2

LOOP DETECTOR;DETECTOR TESTER-MINI SIZE.&.GREAT FOR INSTALL TEST & COMMISSIONING, US $15.00 – Picture 3

LOOP DETECTOR;DETECTOR TESTER-MINI SIZE.&.GREAT FOR INSTALL TEST & COMMISSIONING, US $15.00 – Picture 4

Loop Detector;detector Tester-mini Size.&.great For Install Test & Commissioning

US $15.00

Queluz , Sintra, Portugal
Jan 29th

Open on mobile:
QR code

WLD - WORLD LOOP DETECTORS THANK OUR EBAY.COM BUYERS HELPING US GROW ! WLD WILL ALWAYS OFFER "INSTALLER FRIENDLY" PRODUCTS AT "INSTALLER FRIENDLY" PRICES ! A HAND MADE ITEM; A LOW COST, BUT VALUABLE, SERVICE TOOL FOR LOOP & DETECTOR INSTALLERS "WLD" MINI DETECTOR TESTER; A LOW COST VALUABLE TOOL THAT ALL LOOP INSTALLERS CAN EASILY CARRY. DISPEL ANY DOUBTS; FOR FAST EASY TESTING OF ANY STANDARD COMMERCIALLY AVAILABLE INDUCTIVE VEHICLE LOOP DETECTOR. WHAT COULD BE EASIER? CONNECT DETECTOR TESTER - POWER UP DETECTOR -DETECTOR WILL TUNE AS NORMAL IF OK USING A JAR LID or METAL TOOL – BRING A METALLIC OBJECT CLOSE TO THE "WLD" DETECTOR TEST LOOP BODY; ANY PROPERLY FUNCTIONING VEHICLE LOOP DETECTOR SHOULD "TRIGGER" & INDICATE A “DETECT” CONDITION IF IT IS WORKING OK TAKE AWAY THE JAR LID or METAL TOOL – THE LOOP DETECTOR SHOULD “UN-DETECT” – AND REVERT TO NORMAL “STANDBY” STATE - IF DETECTOR IS PROVED OK - DISCONNECT DETECTOR TESTER & RETURN IT TO TOOLBOX IF DETECTOR IS NOT PROVED OK, WE RECOMMEND CHANGING DETECTOR AND CONFIRM REPLACEMENT IS OK BY REPEATING PROCEDURE. ITS QUICK, SIMPLE, LOW COST, AND WORKS WITH ANY "INDUCTIVE" VEHICLE LOOP DETECTOR. TO USE AS A SUBSTITUTE LOOP FOR TEST & COMMISSIONING; CAN BE SUBSTITUTED FOR A FIELD LOOP TO ALLOW INITIAL TESTING WITHOUT USING VEHICLES IN A ROADWAY. IDEALLY IF EACH FIELD LOOP IS DISCONNECTED, AND A WLD TEST/DUMMY LOOP PUT IN ITS PLACE AT THE DETECTOR LOCATION, AN ENTIRE SYSTEM CAN BE PRE-COMMISSIONED WITHOUT THE USE OF "TEST VEHICLES" INTERRUPTING NORMAL TRAFFIC FLOW TO USE AS A DUMMY LOOP; HAVE ONLY A DUAL LOOP DETECTOR TO DRIVE ONE LOOP. FIT THIS ITEM AS A DUMMY LOOP ON THE "UNUSED" LOOP INPUT - THE DETECTOR WILL BE PROPERLY LOADED BY THE LOOP AND RUN WITHOUT SHOWING FAULT STATE (DUE TO "OPEN CIRCUIT" LOOP INPUT) If there is any doubt about the functionality of a vehicle loop detector, it is a simple and fast job to disconnect the loop on site, and connect the WLD MINI DETECTOR TESTER in its place. Something that can be done in seconds! Operation is by using a metal test object; almost any metal object from a tool box (spanner, box-lid, etc.) as a "vehicle substitute" which simulates the changes seen by a vehicle loop detector when a vehicle is “detected” . The WLD Detector Checker offers easy One-Man-Operation to check correct detector operation AND makes installation test simulation so much simpler as no test vehicles are required to traverse installed loops as in common live commissioning and test procedures. The Unit comprises a hand wound "loop" coil on a PVC pipe former. The Detector Checker can be used to test systems in a workshop environment, or on site, as it can be used as a "Substitute" ground loop when connected to an inductive vehicle loop detector. This allows any style or size of vehicle detection loop to be simulated by a device about 6cm. (2.5 inches) long. NOTE THAT WE MAKE FULLY TESTED LOOPS, FOR ALL USES & IN ALL SIZES, STOCK & TO ORDER. PLEASE MAIL FOR DELIVERY AND PRICING DETAILS. THANK YOU. Returns Policy: Should you wish to return your purchase within 14 days of receipt please first ask for a “Return Authorization Number (RAN) Request Form”. This simple document will be emailed to you to be completed and mailed back to us. When received we will advise your “RAN”. Any item/s returned MUST be as dispatched and include all original packaging, inserts, and be complete with any accessories in order to receive a full credit for the product/s being returned. The buyer is responsible for payment of the return costs, by any service the Buyer chooses. NO refunds will be made before goods are received back at our point of dispatch. The original dispatch cost from our stores to the Buyer will be refunded in full, in part, or not at all, at our sole discretion, dependent on circumstances, information provided, and condition of returned goods.

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	W L D World Loop Detectors
Type	DETECTOR TESTER & TSET/COMMIONING LOOP
Model	MINI DETECTOR TESTER & LOOP SUBSTITUTE
Country of Manufacture	Portugal