US $18.00
Condition: |
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details.
...
|
Manufacturer | Lyndex |
Model | 5C | ||
Country/Region of Manufacture | Japan | ||
MPN | 500-060 | ||
Brand | LYNDEX CORP. |
Directions
Similar products from Metalworking Collets
1-5/16" Warner & Swasey #5-1A Collet, 471-1002 Nardco
1-55/64" Warner & Swasey #5-1A Collet, 471-1002 Nardco
1" Square Warner & Swasey #5 Collet, 4669-1004 Nardco
1/2" Hex Warner & Swasey #5 Collet, 4669-1004 Nardco
1-3/16" Warner & Swasey #5 Collet, 4669-1004 Nardco
1-23/64" Warner & Swasey #5-1A Collet, 471-1002 Nardco
1-7/64" Warner & Swasey #5-1A Collet, 471-1002 Nardco
1-1/8" Square Warner & Swasey #5 Collet, 4669-1004 Nardco
5x Precision SUJ2 ER16 Spring Collet 6mm Diameter HRC 45 degC Hardness
2x ER16 Spring Collet ER-16 Chuck SUJ2 HRC 45 degC Hole Diameter 7mm
COLLET AF-269 1" FLEX COLLET AF200 SERIES 25.5MM #7295
COLLET AF-280 1-1/4" FLEX COLLET AF200 SERIES #7294
HORIZONTAL/VERTICAL COLLET INDEXER
10 ASSORTED 5C MACHINABLE / EMERGENCY COLLETS 8 w/ INTERNAL THREADS
KENNAMETAL - ERICKSON TG75 COLLETS SEE DESCRIPTION FOR SIZES AVAILIBLE
Lot of 3 collet adapters ? stop plug
People who viewed this item also vieved
Jergens 41102 1/4" 2 Piece Self Aligning Spherical Washer USA MADE
DE-STA-CO CLAMP FLAT-TIP BONDED NEOPRENE SPINDLE MODEL 225208M (QTY.2) #1910
Hardinge CHNC 8 Station Turret Plate For CC Tool Holders
MACHINIST MILL LATHE TOOL NICE Toolmakers Ground Hardened Honing Plate Fixture
MACHINIST MILL LATHE TOOL NICE Toolmakers Set Up Plate Fixture Hardened & Ground
H&R MFG HR-464-P Chuck Jaw, Soft, T/G, 10 In Chucks
??LASSY GB4-16 RAPID LOAD MAGAZINE VISE??
Solid Makita 763054-5A Chuck and Key Set Replacement 3/8-in Capacity Power Tool
GIBRALTAR, 5" 3 Jaw Self Centering Rotating Chuck, 4MT, 2 Pc Jaws, Steel, /KG2/
PanaVise Wide Head Vise Bench Motherboard Jeweler Holder Extra Hand Vacuum Base
Vintage Sears 4 1/2" Swivel Base Bench Vice
Drill lathe Chuck Large Mill work JM Smith Seymour Conn 5"
LOT OF TWO! Bison 8712-5 Solid Dead Center Taper Shank
grinding milling fixture for punch or holding to work on end of shaft
Master Dividing Head and Tailstock
vintage heavy duty cast iron Machinist jack screw jack
Used Haas SC01 Servo Control Box Programmable Single Axis RED Brush
5C Spin Index and Tailstock Set
Vintage LS Starrett No. 54 4" Machinist's Hold Downs in Original Box SHIPS FAST
Setup Blocks; Step; 6"x4" (CTAM 9257)
2.87 X 2.36 X 4.29 MAGNETIC V-BLOCK WITH SWITCH (3402-0997) - MADE IN TAIWAN
Dreamz Tunisian Crochet W/Interchangeable Head-Size J/6mm
Papermania Folk Floral Clear Stamps A5-Banners
NEW! KENNAMETAL TG100 COLLET CHUCK w/ CAT40 SHANK
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies