US $395.00
Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Brand | 3r |
Directions
Similar products from Electrical Discharge Machine Tools
Sunspot 20mm Mini Block (70mm cube) EDM Chuck holder R#0156
Lot of (3) System 3R EDM Dove Tail Fixture Plates
Charmilles ELORODA 110 RAM-TYPE EDM
MACHINIST LATHE MILL Machinist Lot of EDM Graphite
1999 MITSUBISHI QA10 CNC ULTRA-PRECISON SUBMERGED WIRE EDM
MACHINIST LATHE MILL EDM System 3R Chuck ? l
MONITOR PLUG AND RUN CHARMILLES ANY 15 PIN
System 3R EDM Magnetic Indexing Head w/ Magnet Controller
System 3R EDM Rotating Electrode Holder Chuck, 20mm Shank, For Collets
Charmilles EDM Wire, SW-10-A, .1mm / .004" (2 Spools)
Gisco EDM Wire, CuZn 37, .2mm / .008"
Gisco EDM Wire, CuZn 37, .15mm / .006"
Gisco EDM Wire, Somsal Cu 1200 Q89D, .1mm / .004"
System 3R EDM 70mm X 70mm Dove Tail Block
System 3R EDM 70mm X 120mm Dove Tail Block
System 3R EDM Sliding Arm, 3R-261 9710-V00
System 3R EDM Clamp Bar With Dove Tail
People who viewed this item also vieved
Mitsubishi Machine Cnc Lathe Groove Tool GYHRUS16D90-M25L & GYM25LD-H14-060
Clausing 5914 Lathe Leveling Foot
++ NEW HARDINGE CHUCK -FITS A2-5 SPINDLE NOSE- FOR USE ON ALL MODEL 600 COLLETS
HAUSER SK 50 SHRINK FIT HOLDER ROUGHLY 5/8" ID MADE IN GERMANY (LOC1259A)
ETM NMTB 50 1.5" FACE MILL ARBOR 50 SM 1.5 X 2.625E (LOC1260A)
COMMAND CAT 40 5/8" END MILL HOLDER C4E3 0625 (LOC1261A)
MACHINIST TOOLMAKER MADE 1,2,3 BLOCKS SETUP JIG FIXTURE TOOLING
J & S Tool Co. "Fluidmotion" Radii and Angle Dresser
[BELLA]LIH TU-03 supersonic full force grinding machine
Cox 380ml Dual-Component Pneumatic Co-Axial Two-Part Applicator
STAKING TOOL #3025, PAT. AUGUST1902, K&D SPECIAL NEW STYLE WATCH TOOL, FREE SHIP
Procunier #1 Model E 12" Stopbar
Perma Coil 1221-304 M4 x 0.7 Metric Thread Repair Insert Kit w/ Tools Uses Heli
Hougen 12120 5/8-Inch Diameter Rotabroach 1-Inch D.O.C.
Starrett Drive Pin Punch Set, No. S248
Lockformer Air Op. Corner Notcher, for Fittings & Drive Cleats. Pexto Tinsmith.
Lockformer 24 Ga. Pittsburgh w/ Slitting Attach. 2 machines in 1. Pexto Tinsmith
GROBET-VALLORBE ( CUT: 0 ) "SWISS" NEEDLE FILE ( STYLE: MARKING ) 4" LG.
GROBET-VALLORBE ( CUT: 0 ) "SWISS" NEEDLE FILE ( STYLE: WARDING ) 4" LG.
NICHOLSON ( CUT: 0 ) "SWISS" NEEDLE FILE ( STYLE: WARDING ) 6-1/4" LG.
HIGH SPEED ACORN DIES 5/16 NF24 03091521
BALAS 1/2" ROUND #11C COLLET 03091513
FETTE THREAD ROLLING HEAD F45-1RN-729 w/2 Sets Of 1520939 1-1/8" to 1-3/16 DIES
Vectrax - 450 - Vertical Bandsaw w/ Welder, 18" variable speed 3 phase 220 volt
DOALL C-80 FULLY AUTOMATIC HORIZONTAL BAND SAW AUTO FEED 12" X 16" CAPACITY
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies