US $400
Directions
Similar products from Supporting Blocks & Sets
Good Lot Of Six Machinists Blocks Set Of Four Parallels 1", 2" 3" Used Set
MAGNETIC BLOCKS TOOLMAKER MACHINIST alluminum steel set of 4
Machinist / Toolmakers Bench Block 4 x 3 x 2 1/8
Vintage Machinist Tool Lot Parallels V Block
Machinist Precision V-Block Sine Blocks - Qty. 2 - Hardened w/ Components
V Block & Clamp - 1-5/16" CAP - SPI (91-290-7)
Small Unmarked Mill V-Block,w/ Clamp,1 x 1-1/16 x1-7/16~NICE #MB30216
KODAK 1 INCH VERTICAL VEE BLOCKS, 2 BLOCKS FOR ONE MONEY
MCH 1/2 Precision parellel set 4 matched pairs
V-Block; Brown & Sharpe # 750-B (CTAM 9471)
V-Block; Magnetic; Two Sides (CTAM 9473)
Starrett No. 54 Hold Down 6" qty 1
2 Vintage Little Machinist Vises 1 1/4" x 1 1/8" Square
V-Block & Clamp Set, 2.5" x 2.5" x 2 x 1-3/8 Cap, 420-5611 |JC2|
ROTATOR VICE PIECE WAS WITH VEE BLOCKS WITH READINGS AROUND BASE
MACHINIST 123" THREAED PRECISION PARALLEL MILLING BLOCKS(2)
Machinist Right Angle Set up Block, L Block, Boring Block, Machinist Tool
Lot 3 Machinist set of V Blocks & Milling Tapped Holes Flat surface plate block
People who viewed this item also vieved
VCFC1678 5/16" Valenite Coolit Collet 93-371-1380
VCFC1656 Valenite CoolitbCollet 93-371-1379
12 Pcs. Phase II Hex & Square 5 C Collets With Inside & Outside Thread
Vintage Cincinnati Tool Co No. 540 4” C Clamp INV9991
Suburban Tool indexing face plate fixture, v block, WG1- 6 machinist tool
(5) Machinist Angle Block s, Plate, All are 3" - 5" Tall x 2" - 4" Wide, Hardene
DESTACO 235-U HORIZONTAL TOGGLE CLAMP 235U Detroit Stamping De Sta Co
One Starrett No.161-D Tool Makers, Machinists, Parallel Clamp
LOT OF MACHINIST PARALLEL CLAMPS work holding tool 1 ARMSTRONG No 12 & Others
9 CUTTERS FOR UNIMAT SL1000/DB200 LATHE NEW!
VINTAGE 6'' COLUMBIAN BENCH VISE - #506 LOCAL PICK UP ONLY!
Old 3" Machinist Drill Vise Model 108
Enco # 751 Live Center w/ # 1MT / FB 9
MT6 CARBIDE TIPPED CENTER MILLING GRINDING WORKHOLDING
Heavy 8 3/4" Long Large Live Center From Vintage Metal Lathe 1.25"-1.05" Taper
NOS Cushman 4 Inch Lathe Chuck
6 jaw chuck for lathe for watch repair watchmaker lathe
BUCK 4" 6-JAW LATHE CHUCK , 5 C MOUNT HARDINGE LATHE
8x LOT NEW ALSTOM POWER NUT GP-2375-B 1-5/8" HEX HEAVY JAM 1-5
Used Edward Andrews Steel Boring Bar Sleeve, 4" L, 1.5" OD, 1/2" Bore, EA48-1
Used Edward Andrews Steel Boring Bar Sleeve, 1.50" O.D., 4" Length, EA48-2
HRT210 HAAS Rotary Table 4th Axis
Troyke 15" rotary table model U15
PALMGREN Rotary Slide Tilting Table, 8 In, X-Y 4 jaw chuck
Collet Chuck for Brown & Sharpe #11 1-1/2" Straight Shank +3/8" Serrated Collet
DA-400 Double Angle Collet Chuck NMTB-50 Taper Shank
15 Pcs Grand No21 Collet Set 1/8" to 1" + Chuck # 521 W/Wrench Made in Germany.
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies