Weeke Bp 140 Cnc Machining Center W/ Auxiliary Spindle & Flat Table 4x10, 4x12

US $8,000.00

Zeeland, Michigan, United States
Aug 21st

Open on mobile:
QR code

This was one of our back up machines we sent to EX-FACTORY to sell. You may still see the original EX-FACTORY listing here on ebay. (Just to clarify we do own it) they have listed for $16,500. Need it moved ASAP. Will load on your truck. We have a few tool holders etc. as well to get you started. Sold as is. Expect some minor work and a couple hours on free tech line with stiles if not familiar with Weeke but you should be up and running same or next day. We moved this machine a couple times and always had back up and running within a couple days. Good starter machine that was in good working order when removed. It is almost 20 years old but has plenty of life in it yet. Great for a small shop or dedicated product line, back up. Table is 51' x 126" and we ran 4'x12' sheets by just adding an extension on the left side to support the additional 18". Over all axis travel is 51" x 148" *The drill banks were never used originally and we had just started hooking the lines back up to them when removed for storage. All should work, they were just disabled from new to avoid crashing for the specific product line it was used for. Currently there are 8 hooked up and running perfectly. It is as simple as running airlines and activating in the control software. WEEKE BP 140 CNC Machining Center with Auxiliary Routing Spindle & Flat Table Specifications: Work area capacity: X-Axis 110.25" (2,800 mm), Y-Axis 41.34" (1,050 mm). Reconfigured on upgrade, Actual travel is 148" in the x axis and 52" in the y axis X-Axis Stroke 148", Y-Axis Stroke 52", Z-Axis Stroke 10.24" (260 mm). Rapid traverse speeds: X-Axis 263 FPM (80 MPM), Y-Axis 196 FPM (60 MPM), Z-Axis 64 FPM (20 MPM). Work table: (8) Panel support benches with 51" x 126" Flat table, (Seller has cut 4' x 12' Sheets with an extension support). Equipped with: Boring unit: (1) 2 HP (1.5 kW) Motor, 4,000 RPM, (21) Independent vertical spindles, (10) X-Axis, (10) Y-Axis, (1) Offset spindle for up to 35 mm (1.38") Diameter Drills, (1) Independent 4-way Horizontal boring block with (6) Spindles: (2+2) X-Axis & (1+1) Y-Axis, Maximum horizontal boring depth 1.77" (45 mm), (1) X-Axis Grooving saw with 100 mm (3.94") Diameter Blade, 2 HP (1.5 kW) Motor. Routing: (1) 10 HP (7.5 kW) High speed vertical electro-spindle (Main spindle) with HSK F63 Adaptor router, 11 KVA Frequency inverter, Programmable speeds 1,000 - 18,000 RPM, 5 kW (6-1/2 HP) Auxiliary routing spindle with .98" (25 mm) ETP Hydro clamping chuck, 8-Position Ride along automatic tool changer. IPC Front End: WEEKE "HOMATIC-2000" with WINDOWS & WOODWOP Version 4.5 Operating system; 17" Color monitor, Industrial keyboard, 1.44 MB Floppy disk drive, 2 GB Hard drive, 32-bit Processor, Ethernet interface, RS-232 Serial interface. NUM Programmable logic control (PLC) for linear, circular & helical interpolation, All mounted in separate free-standing control cabinet, Pedestal, Pendant & (2) Foot pedal controls. Complete with: Manuals. NOTE: No Vacuum Pump. Will negotiate a 40hp Dekker pump and a back up control PC with all software on it for this machine with offers of at least 8k. NOTE: Photos were recently taken of installed machine. Machine was then de-installed and stored. NOTE: Safety mats are included but are currently jumpered out in the cabinet. They all worked but never reinstalled when moved the second time. Power Requirements 230/460 V, 60 Cy, 3 Ph. Dimensions: 265" x 104" x 120" H. Weight: 11,500 Lbs. Truck requirements: Figure 8' wide by 25' long x 7' high truck bed space. Add another 6'Dx8'Wx6'H and another 2,500lbs for the vacuum pump if negotiated. Buyer must arrange for a truck to pickup. We will load. Looking for an offer of at least 8k+ to consider including pump and extras. You will spend that on a 40hp vacuum pump or the extras alone if replacing them. Payment by wire or cleared company check before removal. SOLD AS IS. As with any older machine expect some minor repairs to make fully functional. If you are familiar with Weeke machines you will know that a sensor or relay may need to be replaced after they have been in storage a while and/or have been moved. Just typical for these machines. We will include some extra's we kept on the shelf.

“Fair - Good. Pulled from working environment.”

Machine Type

3 Axis Router Machine

Brand

Weeke

MPN

BP140

Control

CNC

UPC

Does not apply