Wire Shelf Clips Anchors Clip Rated 167lbs 5pc set #50250 Better than Rubbermaid, US $1.98 – Picture 0

Wire Shelf Clips Anchors Clip Rated 167lbs 5pc set #50250 Better than Rubbermaid, US $1.98 – Picture 1

Wire Shelf Clips Anchors Clip Rated 167lbs 5pc Set #50250 Better Than Rubbermaid

US $1.98

Seattle, Washington, United States
Jan 30th

Open on mobile:
QR code

Much better than the cheap Rubbermaid and a lot cheaper. 5-Pack Wire Shelf Anchors with Retainer Clips and #8 x 1-3/4-in Screws Holds up to 167 lbs in 1/2 In. drywall with #8x1-3/4 In. combo head screw included in the package (Industry standards recommend 1/4 of this ultimate load per anchor) Locks on walls 3/8" to 1/2" thick for vibration-proof holding but also works in thicker (e.g., plaster) and solid (e.g., concrete or brick) walls Included retainer clip prevents tipping and installs with the same screw that holds the wire shelf Weight rests on the screw for maximum security and safety No More Fumbling with Shelving Standards The built-in spacer is made to fit flush with shelving standards (C-channel) to ensure accurate alignment and to prevent the anchor from being jacked out of the wall during installation. May be also used as a stand-off for installing equipment on warm or wet walls when ventilation is needed behind the installed object. Part number 50260 = Bag of 7 TBS1 TOGGLER Shelving Anchors, 7 #8 x 1-3/4" combo head screws & 1 setting key. Part number 11023 = Box of 50 TBS1 TOGGLER Shelving Anchors & 3 setting keys Step-By-Step Position standard on wall and hang it loosely by a nail from top screw hole. (Gravity will hold standard straight.) Mark the remaining screw hole locations. Remove nail and standard. Drill a 5/16" diameter hole at each mark—minimum hole depth in solid walls 1-1/4+. Fold anchor, insert in hole, and tap flush with wall. Insert black key to pop anchor open behind wall (except in thick or solid walls). DO NOT HAMMER KEY. Remove key. Place standard over anchors. Insert screws and tighten until flush with standard—then stop. Use enclosed screws or any #7 x 1-3/4" flat head screw. The anchors also wedge securely in thick and solid walls. Do NOT use key. Position and install additional standards on wall, leveling top of each with top of first standard. For double-slotted standards, use TOGGLER® Pegboard Anchors TBS2. Materials TOGGLER Specialty Anchors can be used in almost any material, including: Gypsum Board Drywall Plasterboard Plaster Accoustic Ceilings Tile over drywall All TOGGLER Specialty Anchors can be used in any material (concrete, plywood, paneling, drywall, etc.) of any thickness above their minimum grip range.All TOGGLER Specialty Anchors install in the wall like our TOGGLER Hollow-Wall Anchors, and wedge securely even if you hit a cavity in the wall with your drill. Each requires only a 5/16" (?8mm) diameter drill bit. Additional Information Technical Bulletin > Downloadable PDF Shelving Applications/Solutions > Shelving

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Type	Drywall Anchor
Brand	Toggler
Head Style	Pan Head
MPN	50250
Drive Style	Phillips-Slotted
Length	1.75 inches
Size	#8