US $242.86
Saint Charles, Missouri, United States
Jan 30th
Contact Seller
Complain
Open on mobile:
SquareTrade © AP6.0 Lottes Roofing 1853 C Sherman Dr. St. Charles, MO 63303 We will work with you to give you the best deal on your EPDM, TPO, Modifed Bitumen, Roofing Shingles, Roof Coatings, Insulation and Roof accessory items!! Call or Email us TODAY!!! "Over 30 years experience in single ply flat roofing products!" Click Below for Certification, Qualification and Reference Data Click Here for Lottes Roofing Information 1-888-895-4465 This 10' x 25' 45 Mil EPDM REINFORCED black rubber roofing roll weighing 79 lbs Includes the Adhesive! 2 - 1 gallon pails of latex bonding adhesive included USA Made 10' x 25' 45 mil Reinforced 5 times Stronger than standard 45 mil EPDM and 3 times Stronger than standard 60 mil EPDM Check out my other items Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required. · 1 Clean the roof surface of all shingle debris and nails. Re-fasten any loose roof boards. · 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8" without risk of possible adhesion issues. · 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane · 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane. · 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3” seam tape if required to splice 2 pices of EPDM deck sheet together. · 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof. Seam tape application if required to join 2 sheets together • Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. • Clean and/or prime the seam area of both rubber sheets using EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area • Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2" out from the edges of the bottom sheet. • Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. • With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. • Remove the paper backing by pulling out from under the top sheet at a 45? angle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. When buying EPDM rubber roofing you need to purchase the proper accessories from us to insure a proper and complete roof installation. We have listed all our EPDM accessories in our EBay store. 200 page Specification & Installation guideline online manual available at Lottes Roofing Specs Page Roof Installation Videos Our Technicians can design and determine what you need for your roofing project and give you a complete estimate for your materials as well as instruct you about your installation process!! EPDM is extremely flexible, much like a tire innertube, and extremely strong. EPDM has over 200% elongation, and it's performance characteristics are stable in temperature ranges from -50 to 240 degrees Farenheit before failure. The EPDM membrane also exhibits over 1,300 lbs psi tensile strength, and 150 psi tear strength. Though there are other types of roofing membrane material in the marketplace today, none of them meet all the positive characteristics, ease of handling, and price of EPDM. LOTTES ROOFING REINFORCED EPDM SPECIFICATION DATE ISSUE 1/20/2002 PHYSICAL PROPERTIES ** ASTM TEST METHOD UNITS MINIMUM ASTM SI Eng THICKNESS D-412 MM (IN) 1.14 +15/-10% .045 +15/-10% SPECIFIC GRAVITY D-792 GM/CC 1.1 1.1 UNIT WEIGHT D-751 KG/M* (LBS/FT*) 1.6 .32 BREAKING STRENGTH, MIN. LBF/IN D-7004 Type 11,111 mm(lbf) 400 90 PUNCTURE RESISTANCE, MIN D-4833 N(LBS) 270 60 RESISTANCE TO OZONE 7 days/100@37.8C* (150*)50% ext D-1149 NO CRACKS NO CRACKS COATING OVER THE SCRIM OR FABRIC D-7004 TYPE 11,111 MM(IN) 0.38 0.015 ULTIMATE ELONGATION, MIN D-412 % 250 250 OVEN AGING AT 116*C/100@37.8C (150*F)50% EXT D-573 ELONGATION AT FABRIC BREAK, MIN., % D-7004 N (lbf) 356 80 ELONGATION AT RUBBER BREAK, MIN., % D-7004 % 200 200 TEARING RESISTANCE, MIN. B-TONGUE TEAR D-7004 N (lbf) 45 10 BRITTLENESS POINT, MAX. 0 DEGREES F D-2317 -45*C -49*F OZONE RESISTANCE D-1149 NO CRACKS NO CRACKS WATER ABSORPTION, MAX., MASS % WEIGHT AFTER IMMERSION 166 HRS @70*C (158*F) D-471 % +8,-2 +8,-2 WATER VAPOR PERMEABILITY (MAX) E-96 PERM MILS 2.0 2.0 FACTORY SEAM STRENGTH D816 SHEET FAILURE OR 60 LBS/IN MIN. 65 70 LINEAR DIMENTIONAL CHANGE, MAX., % D1204 % +/-1 +/-1 CHRONIC TOXICITY SCREENING EPA/821-R-02-013 E-729 METHOD 1000.0 PASSESS PASSES Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, Paypal Fees No sales taxes except for applicable states Shipping US and International Delivery Shipped within 24-48 hours NORMALLY on in stock items, not counting weekends or holidays, Normal Delivery within 2-7 days Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me david@lottescompanies.com BID WITH CONFIDENCE Read my policies on my SquareTrade Seal stwithpolicies
