10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 0

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 1

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 2

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 3

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 4

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 5

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 6

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 7

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 8

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 9

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot of 100, US $59.00 – Picture 10

10" Slatwall Slatgrid Panel Display Metal Hook Peg Hanger Chrome Lot Of 100

US $59.00

Veradale, Washington, United States
Jan 30th

Open on mobile:
QR code

LIMITED TIME OFFER. SUPPLIES LIMITED. superior chrome these are commonly called slatwall hooks of 1/4 inch steel rod the HOOK RODS ARE CHROMED, not zinc plated/anodized. the actual diameter is 15/64 which is 1/64 less than 1/4 the industry commonly rounds up to the nearest 16th the diameter mic's out at .236 a true quarter inch would mic out at .250 anyone who tells you otherwise should be ready to mic out their hook with a digital mic in your presence the production process the reason for the discrepancy is that the rods are prepared from RAW steel at 1/4 inch, standard stock the rod is then made smooth through a process that removes some diameter the rods are then cut, bent, welded and dipped for chrome plating there are 2 styles of WELDS hand arc/torch weld which applies a bead between the plate and rod to the left and right on the face (ugly) spot mechanical weld in an automation process like automobile hoods, fenders, doors etc are done this type of weld is calculated, uniform, and consistent - also way more attractive (cant see it without inspection. see pic) OUR SLAT WALL HOOKS USE SPOT WELDS. CRITICAL MEASURES! the slat boards themselves should be 1/4" thick (distance between backside of hook drop plate and face of tang is 1/2 inch) the gap between the top slat board and the bottom one should be 1/4 inch to 3/8 inch (free and clear tang height is 9/16 or 1/2+1/16) the I.D. of the hole in the tang is 7/32 inch diameter the plate is 1/16 inch thick the hook support drop is just over 2 1/2 inches WEIGHTA box can weigh up 20 pounds depending on the piece count. That calculation is about 2 pounds per 10 pieces. Make sure that the person moving this has a good back and exercises proper posturing when picking up or setting down.

Condition

Used :

An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.

Seller Notes

“LIKE NEW! 10" (inch) SLAT WALL (SLATWALL, SLOT BOARD) CHROMED HOOKS for store, event and rack displays. LIMITED TIME OFFER. SUPPLIES LIMITED. The front end has angled tip without the bubble. Rounded tip not bubbled. Acquired from store closing. These are NOT suitable for use in your garage. If you are looking for hooks by the dozen, divide our piece count by 12 and you get that plus the remainder.”