1PC ADC120-12V Actuator 1PC ESD5550E Controller 1PC MSP6729 Sensor Description 1PC ADC120-12V Actuator + 1PC ESD5550E Controller + 1PC MSP6729 Sensor 1.Introduction: DSE5500E Introduction: 1.The ESD5550 Series speed control unit is an all electronic device designed to control engine speed with fast and precise response to transient load changes. This closed loop control, when connected to a proportional electric actuator and supplied with a magnetic speed sensor signal, will control a wide variety of engines in an isochronous or droop mode. It is designed for high reliability and built ruggedly to withstand the engine environment. Simplicity of installation and adjustment was foremost in the design. Non-interacting performance controls allow near optimum response to be easily obtained. 2.The primary features of the ESD5550/5570 Series speed control unit are the engine STARTING FUEL and SPEED RAMPING adjustments. The use of these features will mimimize engine exhaust smoke experienced prior to attaining engine operating speed. Other features include adjustable droop and idle operation, inputs for accessories used in multi-engine or special applications, protection against reverse battery voltage, transient voltages, accidental short circuit of the actuator and fail safe design in the event of loss of speed sensor signal or battery supply. The ESD5550 Series speed control unit is compatible with all GAC proportional actuators except the ACB2000 electric actuator. When the ESD5550 Series speed control unit is used with a ADC100 Series electric actuator, the DROOP adjustment range will be less due to this actuator's low current demand. PERFORMANCE Isochronous Operation/Steady State Stability ±0.25% or better Speed Range/Governor 1K-7.5K Hz.continuous Speed Drift with Temperature ±1% Maximum Idle Adjust CW 60% of set speed Idle Adjust CCW Less than 1200 Hz. Droop Range 1-5% regulation Droop Adj. Max. (K-L Jumpered) 400 Hz., ±75Hz.per 1.0 A Change Droop Adj. Min. (K-L Jumpered) 15 Hz., ±6 Hz.per 1.0 A Change Speed Trim Range ±200 Hz. Remote Variable Speed Range 500-7.5 Hz.or any part thereof Terminal Sensitivity J 100 Hz., ±15 Hz/Volt @ 5.0 K Impedance L 735 Hz., ±60 Hz/Volt @ 65 K Impedance N 148 Hz., ±10 Hz/Volt @ 1 Meg. Impedance P 10V DC Supply @ 20 ma Max. Speed Switch Adjustment Range 1000-10000 Hz. ENVIRONMENTAL Ambient Operating Temperature Range -40° to +85°C Relative Humidity Up to 95% All Surface Finishes Fungus Proof and Corrosion Resistant INPUT POWER Supply 12 or 24V DC Battery Systems (Transient and Reverse Voltage Protected) Polarity Negative Ground (Case Isolated) Power Consumption 50 ma continuous plus actuator current Actuator Current Range @ 25°C - (Inductive Load) Min. 2.5 Amps Max. 10 Amps continuous Speed Sensor Signal 0.5-120 Volts RMS Speed Switch Relay Contacts(N.O. And N.C.) 10 Amps RELIABILITY Vibration 1G @ 20-100Hz. Testing 100% Functionally Tested PHYSICAL Weight 1.8 lbs. (0.82kg) Mounting Any Position, Vertical Preferred MSP6729 Specification: 3/8 - 24 UNF Threaded 2.5" Length with 6' Shielded Cable All are designed and tested to operate within a temperature range of -65°F to 225°F (-55°C to 105°C) . Magnetic Speed Sensors are with Wire Leads Item Pickup Length Thread Length Lead Length Thread Size Drill Size MSP 6729 2.7 2.25 72.00 3/8-24 UNF-2A .332 ADC120-12 Specifications: PERFORMANCE: Available Torque Max1.0Lb-ft(1.4Nm) Maximum Operating Shaft Angular Travel 25+1degree CW/CCW POWER INPUT: Operating voltage 12VDC Normal Operating Current 2 A at 12VDC 1 A at 24VDC Maximum CurrentContinuously Rated 6 A at 12VDC 3 A at 24VDC ENVIROMENTAL: Temperature Range -54 to 95 Relative Humidity up to 100% All Surface finishes Fungus proof and corrosion resistant PHISICAL: Weight 2.3 kg Mounting Any position, electrical connector at the top preferred RELIABILITY: Vibration up to 20G @50-500 Hz Testing 100% Tested MATING HARDWARE Connector Supplied With Actuator Lever LE1500-2 Rod End Bearings(to attach a 12#20 HD linkage rod to lever) BR100(Right Hand)&BR101(Left Hand)----(Don't include!) Wiring Harness HD120 4ft. harness supplied with actuator, other length available from Actuator--------------(Don't include!) Packing Include: ADC120-12V Actuator-----1Piece ESD5550E controller-------1Piece MSP6729 Sensor------------1Piece 2.Payment: We accept PAYPAL payment. 3.Shipping: We will ship all items within 1-3 working days upon receipt of payment,our goal is: ship it as fast as we can. Standard Shipping: To USA,UK and Australia by ePacket,need 7-12 working days. Expedited/Standard Int'l Shipping by Fedex,DHL,TNT and EMS courier: To USA,need 3-6 business days,To other countries,need 4-8 business days normally.But sometimes int'l delivery is highly depended on the courier company and local customs/duties. Import duties and taxes are not included in the item price or shipping charges.These charges are the buyer responsibility. 4.Warranty&Reture Policy: We encourage all customers to communicate with us through eBay messages. If you have any questions or comments whatsoever regarding our products or listing, we are waiting to hear from you A 1 year warranty is offered for this product.If the product malfunctioned under proper usage per instructions manual within the warranty period, please contact us to obtain shipping instructions and send it back at your shipping costs. 30 days evaluation and investigation takes placed after receiving your return item.A brand new replacement unit will be sent to you at our shipping costs if it meets our warranty requirements. Feedback Policy: We are trying to strive to deliver 5-star customer service,Please leave us correct feedback if you are satisfied our service and item as below : eBay Cross Border Trade powered by Channel Effect
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
