2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 0

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 1

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 2

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 3

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 4

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 5

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 6

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 7

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 8

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 9

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 10

2004 Vijuik 6 STATION Saddle Stitch COVER FEEDER 5 knife trimmer MULLER MARTINI, US $32,950.00 – Picture 11

2004 Vijuik 6 Station Saddle Stitch Cover Feeder 5 Knife Trimmer Muller Martini

US $32,950.00

Pinehurst, North Carolina, United States
Jan 30th

Open on mobile:
QR code

ONE (1) VIJUK321-T SADDLE STITCHING SYSTEM Purchased and installed in NC in 2004 with a price over $120,000 Consisting of: One (1) Saddle Stitcher, Model DQ8E for one up or two up with: · Heavy duty cast base · Hohner stitching heads, top-of-the-line, made in Germany · Two (2) Vijuk large capacity stitching wire despoolers · Heavy duty stitcher carriage for up to four (4) flying stitching heads for less wear, longer life · Oblique sheet monitor which automatically diverts improperly-aligned books unstitched and untrimmed into reject tray · Head up sheet monitor which automatically diverts improperly head up books unstitched and untrimmed into reject tray · Electronic plus/minus caliper control measuring on product spine · Product jam detection to keep spoilage to a minimum · Three (3) heavy duty Reitschle combination vacuum/blower pumps Six (6) Signature Feeders, Model DYQ440E with: · Heavy duty cast base · Each top load/bottom feed flat pile feeder has air/pin separation and two (2) suckers for positive transfer of signatures to the rotary drum · Large rotary gripper drums with one (1) set of self-adjusting grippers (4-96 pages) for effortless, positive control of the signatures · Gripper and vacuum opening for signatures with high or low folio, with or without lap, open or closed head · Individually timed drum feeders, ratio 1:1 or 1:2 · All operator functions on the same side as the pile feeder · Product jam detection keeps spoilage to a minimum · Electronic monitoring in each station for missing signature placement onto the saddle which automatically diverts previously gathered signatures untrimmed and unstitched into the reject tray One (1) Cover Feeder, Model ZYDY440E with: · Heavy duty cast base · Top load/bottom feed for continuous production · In-line spine scoring and folding · Missing cover detector which automatically diverts signature unstitched and untrimmed into reject tray · Product jam detection keeps spoilage to a minimum One (1) Missing Stitch Detector One (1) Three-Knife Trimmer, Model QS8E with: · Heavy duty cast base · Quick adjustments by hand wheels/scales located on the operator side · Gentle handling of products; top belt lifts off in parallel to prevent marking · Heavy duty front pressing · Maximum one inch (l ") trim cut off on all three sides · Two (2) sets of knives · Heavy duty knife guides · Front stops assure accurate trimming · Books positively registered to spine · Belt delivery with kicker · Product jam detection keeps spoilage to a minimum · Fourth and Fifth Knifes Electrical (CE Certified): · Central control panel · Lights and machine schematic on control panel for easy location of faults · Fuji Frenic inverter drive system assures accurate, variable speed control · Mitsubishi PLC with Siemens controller assure trouble-free operation of all machine functions · Safety guards electrically interlocked ELECTRICAL DATA: 230 volts(+/- 10 volts), 3-phase plus ground (no neutral), 70 amps, 60 cycle. A nominal line voltage of 220 volts must be maintained to ensure the proper function of the machine and its components.We have all the manuals and spare parts Eric nine one zero six nine two eighteen hundred Also has vacuum waste removal system. Contact me with any questions. We can help load it and know people that will uninstall and reinstall very cost effectively.

Condition	Used : An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
Seller Notes	“Great Condition. Low book count.”