25KW 30-80KHz Mid-Frequency Induction Heater Heating Melting Furnace System, US $6,690.00 – Picture 0

25KW 30-80KHz Mid-Frequency Induction Heater Heating Melting Furnace System, US $6,690.00 – Picture 1

25KW 30-80KHz Mid-Frequency Induction Heater Heating Melting Furnace System, US $6,690.00 – Picture 2

25kw 30-80khz Mid-frequency Induction Heater Heating Melting Furnace System

US $6,690.00

Livingston, New Jersey, United States
Jan 30th

Open on mobile:
QR code

This listing is for a brand new 25KW mid-frequency 30-80KHz induction heater (item# IH25A). Note: This model only available in 460-480 volt three phase. Across International IH series mid-frequency induction heaters are designed to operate between 30 and 80 kHz. Mid-frequency heaters are excellent for small parts heating, cutting, diamond tool brazing, soldering copper plumbing fittings, auto parts heat-treating, annealing of stainless steel containers and more. Mid-frequency induction heaters are the simplest in terms of design and implementation. With their low cost of ownership and maintenance, they are the most popular and reliable machines. The 15kW models are especially popular for their large power capacity and small footprint at an affordable price. This makes them standard equipment for many factories, labs and workshops where 230V AC is available. IH25A Compact Induction Heater Features Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes. Light weight (only 60 Lb), portable (with built-in handle), instant heat and up to 90% energy savings. Precise control with digital time and current displays. Remote foot switch for safer operation. Dual automatic and manual modes. Optional graphite and silica crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size) Custom coil design (fixed coil or coil on a cable so it can be used by hand like a wand). Frequency is non-adjustable, it depends on the coil design (diameter of turns, numbers of turns, copper tubing diameter and total length). ISO 9001:2008 registered manufacturer. We provide sample testing and custom made coils in our New Jersey facility. Safety Features Overvoltage protection: machine shuts down when input voltage is over 495V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 495V. Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself. Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs: One of the machine parts becomes overheated Interfering signal detected Short circuit between work pieces and induction coils Machine malfunctions Induction coils touching each other Input voltage is too low Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously. IMPORTANT Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any injury or damage caused by misuse. Do not run no-load operation for a long period of time, it might cause damage to the machine. Circulating water must be pure, clean and below 45°C. Machine must be grounded properly all the time during operation. Do NOT use single-turn coil if coil diameter is smaller than 4 inches, it will cause high frequency damage to the machine. Thread tape (or related material) is absolutely prohibited during installation of induction coils. Specifications Max. input current 19 A (25A 3-phase circuit breaker required) Power 460 VAC, 50/60Hz, three phase (380V model available upon request) Power distribution cord 10-gauge 4-conductor Max 25A (10/4 SOOW for 3 PH system) Output frequency 30-80 KHz Heating/retaining current 200-1000 A (displayed on control panel) Max. oscillating power 25 KW Max input power 15 KW Duty cycle 80% Heating timer 1-99 seconds Dwelling timer 1-99 seconds Cooling timer 1-99 seconds Water pressure >= 0.2 Mpa (29 PSI) you may use tap water and water pump (>1/4HP & >240 Gph) Water flow 0.5-1.3 gallones (2-5 liters) per minute Induction coil See detail specs below, we will make coils according to your requirements Weight Unit: 60 Lb, shipping: 85 Lb Size Unit: 23x9x18", shipping: 28x14x26" Remote foot switch 7 feet Max. melting capacity 7 Lb (gold, silver, copper), 2 Lb (steel, aluminum) Standard package Part description Quantity Part image IH25A induction heater 1 pc Foot switch (7 ft) 1 pc Induction coil: 5mm diameter, 75x300mm IDxL, adjustable height. Coil wrapped to prevent sparks caused by work piece touching the tube. 2 pcs Water cooling fitting (1/4" x 2, 3/8" x 1 hose barb) 1 set Stainless steel hose clamp 8 pcs Fuse 5 pcs Induction coil adapter (to protect the coil connectors on the machine, good for users who change coils frequently) 2 pcs Operation manual 1 pc

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Across International
Model	IH25A