2pcs Esp8266 Serial Wireless Wifi Module Transceiver 25dbm 802.11b/g/n Esp-06

US $49

ShenZhen, China
Jun 18th

Open on mobile:
QR code

Home Electronic Component Chips Sensor Arduino Module Raspberry Pi 2PCS ESP8266 Serial Wireless WIFI Module Transceiver 25dBm 802.11b/g/n ESP-06 Descriptions: 1. Support 802.11 B/G/N 2. Communication range up to 100 yards depending on environment. 3. Standard 3.3VDC operation with 5V compatible I/O. 4. Standard 3 wire (TXD/RXD/GND) serial communication (idle high) at 115200/8/N/1. 5. Standard 0.1" (2.54mm) half through hole. 6. Upgradeable firmware. 7. Three mode of operations: Client/Access Point/Both Client and Access Point. 8. Support all major security schemes: OPEN/WEP/WPA_PSK/WPA2_PSK/WPA_WPA2_PSK. 9. Support both TCP and UDP communication. 10. Working as TCP/UPD server supports up to five (5) connections. 11. Working as station can connect up to 5 TCP/UPD servers. The ESP-02 can connect to all standard non-SSL websites in the world. 12. Simple AT commands for all operations. 13. Connection based data reception or transparent data reception. 14. Programmable client connection inactivity timeout. 15. Automatic domain name address resolution for public domain name but not the local name within the local area network (router). The following is the list of AT commands: 1. AT-Attention 2. AT+RST-Soft reset 3. AT+GMR-Retrieve firmware version 4. AT+CWMODE-Operation mode selection 5. AT+CWJAP-Join network 6. AT+CWLAP-Available network listing 7. AT+CWQAP-Exit network 8. AT+ CWSAP-Setup network name, password, radio channel and security scheme 9. AT+ CWLIF-Listing connected stations 10. AT+ CIPSTATUS-Connection listing 11. AT+CIPSTART-Initiating connection 12. AT+CIPSEND-Sending data 13. AT+CIPCLOSE-Closing connection 14. AT+CIFSR-Displaying IP from access point 15. AT+CIPMUX-Single or multiple connection selection 16. AT+CIPSERVER-Socket server on/off 17. AT+CIPMODE-Serial port transparent or connecdtion based data output selection 18. AT+CIPSTO-Socket server automatic connection timeout setting 19. +IPD-Serial port connection based data output 20. AT+CIOBAUD-only available with firmware .923 or newer. Also .923 firmware default baudrate is 9600.firware .91 and .92 default baud rate is 57600 and 115200 respectively. Package Included: 2 x ESP8266 Serial Wireless WIFI Module Transceiver 25dBm 802.11b/g/n ESP-06 Payment Shipping Refund We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund. If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.