3-M Scotch-Weld Two Part Epoxy Adhesive 2216 B / A ""GRAY"" Tube Kit 4oz NEW, US $28.00 – Picture 0

3-M Scotch-Weld Two Part Epoxy Adhesive 2216 B / A ""GRAY"" Tube Kit 4oz NEW, US $28.00 – Picture 1

3-M Scotch-Weld Two Part Epoxy Adhesive 2216 B / A ""GRAY"" Tube Kit 4oz NEW, US $28.00 – Picture 2

3-M Scotch-Weld Two Part Epoxy Adhesive 2216 B / A ""GRAY"" Tube Kit 4oz NEW, US $28.00 – Picture 3

3-M Scotch-Weld Two Part Epoxy Adhesive 2216 B / A ""GRAY"" Tube Kit 4oz NEW, US $28.00 – Picture 4

3-M Scotch-Weld Two Part Epoxy Adhesive 2216 B / A ""GRAY"" Tube Kit 4oz NEW, US $28.00 – Picture 5

3-m Scotch-weld Two Part Epoxy Adhesive 2216 B / A ""gray"" Tube Kit 4oz New

US $28.00

Woodhaven, New York, United States
Jan 29th

Open on mobile:
QR code

Brand New In the Box- Free Shipping Within USA Exp Date June / 2016 3-M Scotch - Weld two part Epoxy Adhesive 2216 B / A "" GRAY "" Tube Kit. This item comes with both tubes and mixer stick. Part A is 2 oz. and part B is 2 oz. This is a flexible two part epoxy with a 1 to 1 mix ratio, 90 minute work life and handling strength in 10 hour. Product Description 3M™ Scotch-Weld™ Epoxy Adhesive 2216 B/A is a flexible, two-part, room temperature curing epoxy with high peel and shear strength. Scotch-Weld epoxy adhesive 2216 B/A is identical to 3M™ Scotch-Weld™ Epoxy Adhesive EC-2216 B/A in chemical composition. Scotch-Weld epoxy adhesive EC-2216 B/A has been labeled, packaged, tested, and certified for aircraft and aerospace applications. Scotch-Weld epoxy adhesive 2216 B/A may be used for aircraft and aerospace applications if proper Certificates of Test have been issued and material meets all aircraft manufacturer’s specification requirements. Handling/Curing Information Directions for Use 1. For high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed. However, the amount of surface preparation directly depends on the required bond strength and the environmental aging resistance desired by user. For suggested surface preparations of common substrates, see the following section on surface preparation. 2. These products consist of two parts. Mix thoroughly by weight or volume in the proportions specified on the product label and in the uncured properties section. Mix approximately 15 seconds after a uniform color is obtained. 3. For maximum bond strength, apply product evenly to both surfaces to be joined. 4. Application to the substrates should be made within 90 minutes. Larger quantities and/or higher temperatures will reduce this working time. 5. Join the adhesive coated surfaces and allow to cure at 60°F (16°C) or above until firm. Heat, up to 200°F (93°C), will speed curing. 6. The following times and temperatures will result in a full cure: 7. Keep parts from moving until handling strength is reached. Contact pressure is necessary. Maximum shear strength is obtained with a 3-5 mil bond line. Maximum peel strength is obtained with a 17-25 mil bond line. 8. Excess uncured adhesive can be cleaned up with ketone type solvents.* Adhesive Coverage: A 0.005 in. thick bondline will typically yield a coverage of 320 sq. ft/gallon

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Scotch
MPN	2216
Model	Scotch Weld
Country/Region of Manufacture	United States