3 Occupancy Sensors Dayligh Controllers Switch Relay Circuit Power Pack, US $190 – Picture 0

3 Occupancy Sensors Dayligh Controllers Switch Relay Circuit Power Pack, US $190 – Picture 1

3 Occupancy Sensors Dayligh Controllers Switch Relay Circuit Power Pack, US $190 – Picture 2

3 Occupancy Sensors Dayligh Controllers Switch Relay Circuit Power Pack, US $190 – Picture 3

3 Occupancy Sensors Dayligh Controllers Switch Relay Circuit Power Pack, US $190 – Picture 4

3 Occupancy Sensors Dayligh Controllers Switch Relay Circuit Power Pack, US $190 – Picture 5

3 Occupancy Sensors Dayligh Controllers Switch Relay Circuit Power Pack

US $190

New Smyrna Beach, Florida, United States
Jan 29th

Open on mobile:
QR code

Set of 3 • Used with Low Voltage Sensors • Multiple Sensors • Multiple Loads • AC Switching Only HIGHLIGHTS • Dual Voltage Transformer • Self-Contained Relay • Patented Relay Circuit Protection (Tested to over 400,000 cycles) • Powers up to 14 sensors SPECIFICATIONS • Size:(1/2” inch chase nipple not inc.) PP-20-2P: 41/8 x 3” x 17/8” PP-20 & SP-20: 3” x 21/4” x 17/8” • Mounting: 1/2” inch chase nipple • Operating Voltage: 120, 240, or 277 VAC (Single Phase only) • Each Relay: 20 Amps • 1 HP Motor Load • Output Voltage: 15 VDC, 150 mA at 120 or 277 VAC • Class II: 18 AWG, up to 2,000 ft. • Plenum Rated • Relative Humidity: 20 to 90% non-condensing • Operating Temp: 14? to 160? F • Storage Temp: -14? to 160? F • UL and CUL Listed • 5 Year Warranty • Made in U.S.A. LOW TEMP/HI HUMIDITY(-LT) • Conformally Coated PCB • Operates down to -40? F • Corrosion resistant from moisture Power Packs are the heart of the Low Voltage Sensor System. The PP-20 transforms 120, 240 or 277 Volts (single phase) to class II 15 VDC to power the remote sensors. Utilizing Patented Relay Circuit Protection the PP-20 also switches the lighting load "On" and "Off": Tested to over 400,000 cycles at rated load! Although Plenum Rated, the elongated mounting nipple allows for the PP-20 to be mounted either directly thru a 1/2” inch knockout in a junction box, or to be located inside an adjacent box for specific local code requirements. Up to 14 sensors may be connected to one PP-20. Multi-circuit control can be handled by multiple PP-20's, or 2-Pole Power Packs (PP-20-2P) and Slave Packs (SP-20) may be configured. PP-20's can be wired continuously hot (line side), or on the switch leg (load side) without nuisance delays upon turn "On". LOW VOLTAGE OPERATION AND TEST The Low Voltage Wires or Terminal is color coded Red (15 VDC), Black (Common), and White (Occupancy Signal). With no sensors connected, using a small wire, connect the Red terminal to the White. The lights should turn "On". Remove the connection and the lights should turn "Off". With the sensors connected, the Red and Black wires provide DC power to the remote sensors, and when there is occupancy detected, the White wire produces a 15 VDC signal from the sensor to the power pack initiating the lights to "On". Upon initial power up, the Sensors automatically send an "On" signal until the sensors have stabilized and "Timed Out". Thanks For Looking!

Condition:

New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...

Country of Manufacture

United States