US $200
| Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Manufacturer | USA AMERICAN TOOLMAKER MADE |
| Country of Manufacture | United States | ||
| Country/Region of Manufacture | United States | ||
| 30-60-90 1/4"x1.9"x3.3" | 45*-45*-90* with 60* 1/4" x 2.46" x 3.12" | ||
| Model | FIXED ANGULAR PRECISION GAGES |
Directions
Similar products from Fittings & Plates
GE General Electric CR104PXN1BP057 ON/OFF Name Plate
Lots of (5) Taymac 5070W Masque Toggle Switch Cover-Up Plate - Many Available!!
MACHINIST TOOLS LATHE MILL HUGE Machinist Lot of Mandrels
MACHINIST TOOLS LATHE MILL NICE Angle Set Up Plate Fixture for Hold Down
BLACK OXIDE 5 INCH SINE BAR 5/8 X 6
ex CONDITION BLACK OXIDE 5 IN SINE BAR 5 HOLE
Wee Block Set for use with Pin Grinding Spin fixture.
6 Machinist's Jacks General No.7 (1) case NOS
SUBURBAN UNIVERSAL RIGHT ANGLE IRON GROUND FINISH URA 081012 G 8" X 10" X 12"
Hardinge 8 Station Turret Plate w/ CC Tool Holders CHNC CNC Lathe Tools Best Buy
Cooper Crouse Hinds V63 Glass Globe Fixture Fitting
5" Centers Sine Plate! Precision ground! Hardened Steel!
NICE! EAGLE ROCK 5C COLLET ENDMILL GRINDING FIXTURE + 3 HARDINGE COLLETS
HARDINGE 5C COLLET HORIZONTAL / VERTICAL INDEXING FIXTURE + 8 HARDINGE COLLETS
Sine Plate 6 Inch By 3 Inch Shop Made Tapped Holes for 1/4 -20 Cap Screws
Set Up Block Hollow Hexagon Machining Milling Lathe Toolmaker
Set Up Block Hollow Square Machining Milling Lathe Toolmaker
Set Up Block Round Cylinder & Mixed Bearings Machining Milling Lathe Toolmaker
Indexing gear tool Mill with center head Milling machine machining cutter bit
People who viewed this item also vieved
ZIP STEPPED CAST IRON BLOCKS MACHINIST MULTI-STEP IN 1/4", 1/2", 3/4" & 1" STEPS
LUFKIN No.905 V-BLOCK SET MATCHED TOOLMAKER VINTAGE
BROWN & SHARPE MATCHED PAIR V-BLOCK HARDENED 750B,# 462, 2 Clamps
NEW MT4 LONG NOSE LIVE CENTER MORSE TAPER 4 MEDIUM DUTY LATHE LIVE CENTER
Skoda Live Center Sets New Live Center MT# 4
MORSE TAPER #4 DEAD CENTER NEW
6"Yelok Flat Jaws in steel 1.5x60?Kitagawa,Howa and other chucks
IMS Tool Holder Part - Collet chucks holders without nut w/treated nipple - NEW!
Toggle Clamp Base De-Sta Co. #640 straight line
Toggle Clamp Base De-Sta Co. #225U
Toggle Clamp Base De-Sta Co. #237U
USED UNIVERSAL ENG. SERIES "Y" DOUBLE TAPER COLLET CHUCK 562030 (1"-Shank)
TAC KWIK-SWITCH 200 ACME NUT, P/N: TAC-P200-17 ~NEW~SURPLUS~
USED BALAS C3 CAT-40 COLLET CHUCK (40MM-VF-4-C3) CAT40
Lyndex 15/16" 5C Collet, 500-060 Tool Holder Collet-New
5x Precision SUJ2 ER16 Spring Collet 6mm Diameter HRC 45 degC Hardness
1-1/8" Square Warner & Swasey #5 Collet, 4669-1004 Nardco
Hartford 12 Inch Super Spacer Special Index Plate Your Choice of One (1)
Hartford 12 Inch Super Spacer Master Plate - See Listing For Available Indexes
Hartford Index 8 Inch Super Spacer Master Plate - See Listing For Indexes Avail
Troyke Cross Slide Rotary Table (Inv.876)
HAAS CONTROLLER 17 PIN CNC MILL ROTARY CONTROL INDEXER RED HRT210 HRT160 HA5C
UNKNOWN BRAND ROTARY TABLE INDEXER WITH YUASA PROGRAMMABLE CONTROLLER
PanaVise with Circuit Board Holders on 8"x8" Wooden Base
Double Lock Machine Vise, 6-1/4" Jaw Width, 4" Opening, 2" Depth
4" PRECISION BRIDGEPORT MILL VISE WITH SWIVEL BASE PIPEFITTER GUNSMITH M850400
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies