5.4l (1.4gal) Solar Cells Silicone Encapsulant Kit

US $480

Celje, SI-386, Slovenia
May 26th

Open on mobile:
QR code

SOLAR CELLS ENCAPSULANT KIT Solar cells encapsulant KIT includes: Polsil Solar 5l (1.3gal) Katalizator Solar 0,4l (0.1gal) Test report Invoice PRODUCT DESCRIPTION AND APPLICATION Polsil® Solar is two-component liquid silicone rubber which cures at room temperature. Clear the silicone rubber with the addition of curing agent - Katalizator Solar. Polsil® Solar is used in the solar panel manufacturing process for stiffening and protecting (flooding) photovoltaic cells in solar panels against impact of climatic factors in the conditions of variable temperatures ranging from -50 to +180 °C. PREPARATION OF COMPOSITION Measure a suitable dose of catalyst and mix thoroughly and slowly (excessively violent mixing may cause considerable aeration of composition). Processing temperatures should range from +15 to +30 °C. CATALYST DOSAGE Polsil® Solar should be hardened using Katalizator Solar in the amount of 6 to 8 parts by weight per 100 parts by weight of Polsil® (the catalyst is most frequently used in the amount of 8 parts by weigh). ATTENTION! The mixture of Polsil® Solar with the catalyst should be prepared just before use and used up within 45 minutes. Total cross-linking time with 8 parts by weight of the catalyst: maximum 48 hours at air humidity within 40-60 % and at room temperature. FLOODING OF PHOTOVOLTAIC CELLS Place and connect sections of cells on a clean, degreased and levelled sheet of glass. Edges of the sheet of glass should be protected with a frame (e.g. made of aluminium angle sections which should be permanently glued to the glass (the best solution)) in order to prevent outflow of silicone. Next, as much as possible, immobilize the pane of glass with the frame and cells and start flooding the cells. Slowly (a thin stream)flood the cells with the previously prepared liquid composition so as to ensure that the silicone self-actingly fills the space between the glass and cells. After complete "flooding" of cells, check for entrapped air bubbles in the poured composition. Gently remove possibly entrapped air bubbles. Leave the flooded solar panel to allow complete cross-linking of the silicone. ATTENTION! Polsil® Solar is a rubber which cures in contact with air and it must not be tightly closed i.e. with other sheet of glass in order to avoid so-called reversion effect (partial cross-linking). After cross-linking the surface of the panel should be protected by applying 3-5 millimeters layer of silicone rubber Polastosil® M-33 or Polastosil® M-60, and wait for the total cross-linking. Storage: Store in original, sealed containers in well-ventilated rooms at temperature not exceeding 30°C. Safety: The product does not present any particular risk. Not subject to ADR/RID. Producer’s notes: The information contained in this document is given in good faith based on our current knowledge. However, this shall not constitute a guarantee for any specific product features. Each user bears the full responsibility for making its own determination as to the suitability of product for its own particular purpose. Because actual use of product by the user is beyond our control, such use is within the exclusive responsibility of the user, and we cannot be held responsible for any loss incurred trough incorrect or faulty use of the product. We accept the following forms of payment: PayPal Bank Transfer Orders are generally shipped within 48 hours after payment. We are shipping worldwide Of course, customer satisfaction is always our goal - so don't hesitate to either: call us at +386 59 19 19 16 contact us via email at info@sol-air.eu. We accept returns up to 14 days after you receive your order. In order for us to be able to accept your return, your items must be in good condition, and be in the original packaging. Please note that shipping charges are not refundable and a restock fee may apply to special orders. When you receive your shipment, please inspect the packaging carefully. Note any damage to the package with the driver at the time of delivery. Please provide up to 7-10 days for returns to be inspected once we receive it. The Customer is responsible for return freight.