63'' 1600mm Cold Laminator 110v 2200w Full Auto Laminating Machine Large Format

US $1,849.00

Walnut, California, United States
Aug 27th

Open on mobile:
QR code

Hi,Welcome to our store ! 63'' 1600mm Single-side Low heating Cold Laminator 3 years warranty with lifetime technical support and free parts replacement! You can buy with confidence! US Stock! This price is only for the local pick up, if you are far from our warehouse,we can ship it to you,but extra shipping cost will be needed. Kindly Note: Not Include the Air Compressor !!! Description: This laminator 1600C6+ is low heated cold laminator with liner and without liner, a wide range of application. It can be used both cold laminating and hot laminating with low temperature, to strip coil backing paper,to roll picture automatically. Especially when work in hot laminating conditions,it will improve the coating effect by heating the roller,. Its multiple-function,easy operation and high efficiency. Upgraded multi-functional and enhanced version ,which can be used with both hot and cold laminating. Specs: Model SEC-010 Maximum Laminator Width 1520mm (60") Roller’s Diameter 130mm (5") Maximum Laminating Thickness 25mm (0.99") Maximum Heating Temperature when hot laminating, the temperature is 50~60 degree, the highest temperature is 60 degree. Laminating Speed From 0 to 10m (393") per minute Preheating Time 5 - 10mins Power Consumption 0.3 - 0.5KW / h Power Input 2200W Height Adjust Single side lifting link Motor Forward / Reverse Yes Floor Stand Yes Auto Rewind Liner Pickup Yes After Laminating Pickup Yes Emergency Stops Yes Safety Photocell Yes Power Supply AC110V, 50 / 60Hz Details: Application: Applying to indoor and outdoor car sticker,photo and video,rimless no painting mounting and so on. Features: Adopts low temperature cold laminating, mainly used to solve the issue that cold laminated images are hazy. Stainless steel feeding table 130mm (5") upper rubber roller Auto – take – up system Anti – tilt and anti – fold device (Origin) Pressure and height adjust hand wheel Infrared temperature control device Details in photos: 1. The emergency “stop”button 2. Machine leg 3. Cross brace 01 4. 40*60 Cross brace Control Panel: using Instruction: Preset temperature: Find out hot/cold framed switch, choose the "hot ", temperature display screen will light up, the left number is preset temperature, the right number is roller temperature, press “ SET”key and then through “ UP” and“ DOWN” adjust preset temperature, after adjust it and press“ SET”key confirm it. when cold film, the preset temperature is 50 .,the max temperature is 50 .According to the viscosity of the glue, and adjust preset temperature. Turn: This machine don’t have continuous reverse function; In the "continuous" state it only can " turning"; In the "point move" state, through the pedal switch can "turning" or "reverse". Governor knob: clockwise to grow speed, counter-clockwise to slow down; Please select the appropriate speed to ensure the laminating effect, when stop coated please select "point move". A-Pressure adjusting valve B-Pressure adjusting valve C-locking screw nut 1. When the parallelism gap of the rollers is slight, it can be adjusted by the following method: a. Moving screw A to adjust the balance of the roller while it ’ s rising. Find out which side of the roller rises slower, then move the screw outward ( Or find out which side rises faster, then move the screw inward). Then raise and lower the roller until the roller is balanced. b. Move screw B to adjust the balance of roller while it’ s falling. Find out which side of the roller falls slower, then move the screw outward ( Or find out which side falls faster, then move the screw inward). Then raise and lower the roller until the roller is balanced. (Adjust the air pressure to 0.1MPa, the movement of the roller is slower than normal. It’s convenient to observe. ) Film laminating Laminating work is an extremely fine, technical stronger work, for beginners should have experience in the technicians under guidance of Membranae tectoria work, the below only show the general operation. Preheating ready to work: 1. Fall down tne upper nip roller; 2. Press the "continuous" and "turning" switch, governor rotate to the "1"; 3. Open the main switch; 4. Open the "hot" switch and et the heat temperature which we required, then nip roller began to heating. Hot laminating, the preset temperature is 90 , when low temperature/cold laminating, the preset temperature set to 45 (to working temperature need about 10-20 minutes) 5. Take out a roll of film and install into material roller, then let roll into material feeding roller scaffold and pulling the film with the hand, shall ensure the appropriate resistance,through the next to the damping handwheel adjust it. 6. Let framed chart scroll in carton, then packed in rewinding stent and fixed them. The general questions and methods Problem Control panel have no electricity Method: Check the power and emergency button Problem Don’t turn Method: Lift a little the upper roller Adjust friction Tighten sprocket key Contact with motor or governor Problem Laminated paper isn't clear and have white point Method: Increase roller temperature Clean the dust Contact suppliers to replace film Problem laminated paper have pleated bubbles Method: Adjust roller force Put paper in 90 angle into rubber roller Increase speed and reduce temperature Problem Film fold Method: Adjust material-roller’s resistance Adjust to the required temperature Package: Machine Dimension 74" x 27" x 45" (1880mm x 680mm x 1140mm) Machine Weight 240kg Package Fumigation free package Packing Size 81" x 28" x 28" (2060mm x 710mm x 720mm) Gross Weight (400kg) The laminator comes with 2pcs of heating glass tube, 1pcs is on the machine, 1 pcs is in another package. We send the spare 1 pcs of it just in case of any damage during the shipping. Table 1: Accessories Term Quantity Notice Backing sheet reception roll 1 Feeding roll 1 Film roll 1 Black rubber beam weight 1 Finished products roll 1 Hand wheel 1 Rubber mat 1 Left support of feeding roll 1 Right support of feeding roll 1 Fuse 4 2A/7A Video 1 Table 2: Steel stand packing list Item Quantity Notice Steel beam 2 Middle steel beam 1 Left leg 1 Foot wheels contained Right leg 1 Foot wheels contained Hex screw M8 x 80 12 Flat mat 8 12 Bounce mat 8 12 SHIPPING 1.We will ship your item by FedEx, DHL, UPS, EMS, e-Package etc with the tracking number showed on ebay. 2.Your item will be shipped within 1-3 working days after clear payment . 3.The shipping time varies. If by FedEX, DHL,or UPS, 3-4 business days to USA,5-7 business days to other most countries. If by e-packet,7-15 days to USA,and 2-4 weeks to other most countries. 4.Due to the local dispatch or other reasons, sometimes the shipping time will be delay. Please kindly understand Uncertainties by the delivery company. 5.If you have not received your shipment within 30 days from payment, please contact us. We will track the shipment and get back to you in 24 hours. Our goal is best customer satisfaction! PAYMENTS 1. we accept: Paypal, Please contact us if you may need some other payment method. 2. We will very ppreciate if you can pay for the order after your ordering within 1-3 working days so that we can provide you the best services. 3. Please list your special requests in message after payment. (color, packages, etc.) 4.S&H will be determined based upon your address. PLEASE NOTE: S&H DOES NOT INCLUDE DUTIES, LOCAL TAXES OR ANY OTHER IMPORT FEES. Feedback 1.If you have any problems or concerns to your order or products, please message us and give us a chance to assist before you leave negative feedback. 2.We believe that we can produce a positive outcome to any situation to earn your likes. 3.Your satisfaction is guaranteed. Thanks for your business

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Model	Wide Format cold laminator with Stand
Roller’s Diameter	130mm (5")
Custom Bundle	Yes
Power Input	2200W
MPN	Does Not Apply
Bundle Description	Upgraded 63'' Hot Cold Roll Laminator All necessary accessories
Brand	Unbranded
Maximum Laminator Width	1520mm (60")
Feature	Heat Assistance, auto take up system
Maximum Laminating Thickness	25mm (0.99")
UPC	Does not apply