C $199.00
Condition: |
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details.
...
|
Model | #0557-0008 |
Directions
Similar products from Lathe Chucks
L-00 Type Adaptor for 3 Jaw Chuck Diameter=10'', Spindle Taper L-00, #2700-0502
6-1/4" SMW AUTOBLOK 160 2 CL HIGH PRECISION 2-JAW POWER CHUCK NEW?
The Cushman Chuck Co. @6" 3 jaw chuck Hartford Conn. USA face plate & 2 jaw sets
WESTFALIA 0019-0473-360 SPINDLE CAP CUTTING BORE MACHINE DRILL TOOL PART B212886
84943679 Set (3) Serrated Soft Jaws- F/10" Kita Chuck Howa
Round Machinable Chuck Jaws HC12-41 Performance Jaws 5-1/2" x 3"
THREE JAW 10" CHUCK D-1-6 DIRECT MOUNT
BTC 8" 3 JAW LATHE CHUCK D1-4 MOUNT
Lathe 6" 4-Jaw ChuckMade by Skinner Chuck Co. No.906
D1-3 Type Adaptor, Chuck Diameter = 5", Spindle Taper = D1-3, #2600-0517
3"/75 mm 3-Jaw Lathe Chuck, Plain Back x0.003" TIR w/ 2 Sets of Jaws, #0559-0110
5 / 16 GEOMETRIC LATHE CHUCK 4 JAW
Kitagawa B-206 CNC 6" Power Chuck
3 Jaw 3 Inch Chuck with Key and 3 Screws
D1-5 Camlock Face Plate 12" T-Slot
Hardinge 5C HV vertical and horizontal
ENGLAND! CRAFTSMAN 4" INDEPENDENT FOUR-JAW LATHE CHUCK w/ 3/4" x 16 TPI MOUNT
People who viewed this item also vieved
Series Collet Holding Fixture, Manual, 5C, Horizontal, |IV2| RL
28" Round Sub Plate Steel Fixture/Mounting Plate Drilled and Tapped
6 3/8" SINE BAR / PLATE machinist tools 6 3/8 x 3/4 inches x 1 5/8 " Hardened
CAST IRON SLOTTED ANGLE PLATE OPEN END : 3-1/2" x 3" x 2-1/2"
Riten 6MT Dual Bearing Pipe Nose Live Center 4500 lb. Capacity 65556
Bison 6MT Super Precision Triple Bearing Live Center 7700 lb. Capacity 7-565-106
Erickson180DA0312 Double Angle Collet 5/16"
LOT OF 3 Vintage Cincinnati Tool Co No. 540-3”/No. 572- 2 1/2"/No. 550-3 C.T.Co.
Lot of (14) Small C Clamp, Clamps, 1" to 4", Hargrave, Cincinnati, Stanley, MORE
DE-STA-CO 227-U Horizontal Hold-Down Toggle Locking Clamp with U-Shaped Bar
Heavy Duty Palmgren 4" Machine Machinist Milling Vise. Used
7" X 3" TOOLMAKER GRINDING HARDENED STEEL SCREWLESS VISE USED
"My Sentiments Exactly Clear Stamps 4""X6"" Sheet-True Friends"
"GoDog Bedzzz Bubble Plush Small 23""X17""-Beige"
"Kaisercraft Dies-Beautiful, Cherish, Special To 1.5""X4.25"
MACHINIST TOOLS LATHE MILL Machinsit 2 Ground Mass Tool Co V Blocks ToolMakers
MACHINIST GUNSMITH TOOL MILLING LATHE TOOL LARGE V BLOCK SET UP WORK HOLDING
(LOT OF 2) LUFKIN NO. 905 V-BLOCK With Clamps
CNC Mini Lathe Tailstock Chuck for Rotary Axis 4th Axis A Axis Router Machine
MT2 Morse Taper NO.2 Tailstock Shaft Tail Stock for Rotary Table CNC Router
Rotary Table Horizontal & Vertical 3" / 75mm with 65mm Lathe Chuck for Milling
BROWN & SHARPE ULTRA PRECISION WAVY PARALLEL SET 599-921-25
BROWN & SHARPE WAVY PARALLEL SET 599-921-25
FEDERAL STAND MODEL 100B-20 (# 1015)
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies