Advanced Motion Controls - BE25A20ACG PWM Servo Drive Brushless - Inverted - New, US $399.00 – Picture 0

Advanced Motion Controls - BE25A20ACG PWM Servo Drive Brushless - Inverted - New, US $399.00 – Picture 1

Advanced Motion Controls - BE25A20ACG PWM Servo Drive Brushless - Inverted - New, US $399.00 – Picture 2

Advanced Motion Controls - BE25A20ACG PWM Servo Drive Brushless - Inverted - New, US $399.00 – Picture 3

Advanced Motion Controls - BE25A20ACG PWM Servo Drive Brushless - Inverted - New, US $399.00 – Picture 4

Advanced Motion Controls - Be25a20acg Pwm Servo Drive Brushless - Inverted - New

US $399.00

Santa Clara, California, United States
Jan 29th

Open on mobile:
QR code

PRODUCT DESCRIPTIONS The BE25A20ACG PWM servo drive is designed to drive brushless DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected against over-voltage, under voltage, over-current, over-heating and short-circuits across motor, ground and power leads. Furthermore, the drive can interface with digital controllers or be used stand-alone and requires only a single unregulated AC power supply. Loop gain, current limit, input gain and offset can be adjusted using 14-turn potentiometers. The offset adjusting potentiometer can also be used as an on-board input signal for testing purposes. This drive can use quadrature encoder inputs for velocity control. Power Range Peak Current: 25 A Continuous Current: 12.5 A Supply Voltage: 30 - 125 VAC MODES OF OPERATION ? Current ? Duty Cycle (Open Loop) ? Velocity COMMAND SOURCE ? ±10 V Analog FEEDBACK SUPPORTED ? Halls ? Incremental Encoder ? Tachometer (±60 VDC) COMPLIANCES & AGENCY APPROVALS ? UL ? cUL ? CE Class A (LVD) ? CE Class A (EMC) ? RoHS Power Specifications Description Units Value AC Supply Voltage Range VAC 30 - 125 DC Supply Voltage Range VDC 40 - 190 DC Bus Over Voltage Limit VDC 195 Maximum Peak Output Current1 A 25 Maximum Continuous Output Current A 12.5 Maximum Continuous Output Power W 2256 Maximum Power Dissipation at Continuous Current W 119 Internal Bus Capacitance µF 3600 Internal Shunt Resistance ? 10 Internal Shunt Resistor Power Rating W 50 Internal Shunt Resistor Turn-on Voltage VDC 185 Minimum Load Inductance (Line-To-Line)2 µH 250 Low Voltage Supply Outputs - ±10 VDC (3 mA), +6 VDC (30 mA) Switching Frequency kHz 22 Shunt Fuse A 3 Bus Fuse A 16 Control Specifications Description Units Value Command Sources - ±10 V Analog Feedback Supported - Halls, Incremental Encoder, Tachometer (±60 VDC) Commutation Methods - Trapezoidal Modes of Operation - Current, Duty Cycle, Velocity Motors Supported - Single Phase (Brushed, Voice Coil, Inductive Load), Three Phase (Brushless) Hardware Protection - Invalid Commutation Feedback, Over Current, Over Temperature, Over Voltage, Short Circuit (Phase-Phase & Phase-Ground) Primary I/O Logic Level - 5V TTL Internal Shunt Regulator - Yes Internal Shunt Resistor - Yes Mechanical Specifications Description Units Value Agency Approvals - CE Class A (EMC), CE Class A (LVD), cUL, RoHS, UL Size (H x W x D) mm (in) 186.7 x 107.4 x 62.2 (7.4 x 4.2 x 2.4) Weight g (oz) 1140 (40.2) Heatsink (Base) Temperature Range3 °C (°F) 0 - 65 (32 - 149) Storage Temperature Range °C (°F) -40 - 85 (-40 - 185) Form Factor - Panel Mount P1 Connector - 16-pin, 2.54 mm spaced, friction lock header P2 Connector - 3-port, 5.08 mm spaced, screw terminal P3 Connector - 5-pin, 2.54 mm spaced, friction lock header AC Power Connector - Standard IEC 60320-C14 AC Receptacle (male pins)

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Advanced Motion Controls
Type	Analog Servo Drive
Model	BE25A20ACQ-INV
Compatible With	Brushless, Brushed, Rotary, Voice Coil, Inductive
MPN	BE25A0ACG
Feedback	Tachometer, Hall Sensors, TTL Encoder
Country/Region of Manufacture	United States
Mode	Torque, Duty Cycle (open loop),
Peak Current	25 A
Other Modes	Hall Velocity, Velocity
Continuous Current	12.5 A
Customer Version	INV Version - (Inverted Inhibits)
Supply Voltage	30 - 125 VAC