A rotary evaporator is a device used in chemical laboratories for the efficient and gentle removal of solvents from samples by evaporation. The process of rotary evaporation is most often used to separate solvents with low boiling points, such a n-hexane or ethyl acetate, from compounds which are solid at room temperature and pressure. However, careful application also allows for the removal of a solvent from a sample containing a liquid compound, if there is minimal co-evaporation (azeotropic behavior) and a sufficient difference in boiling points at the chosen temperature and reduced pressure. Example: The following table is a list of a variety of substances ordered by increasing vapor pressure (in absolute units). The new Ai SolventVap 0.5-gallon/2L (evaporating flask capacity) series rotary evaporators come with a modular heating bath, vertical glassware, and digital temperature/rotation control. Its optimized bath volume allows for rapid heat-up times. That’s why our SolventVap evaporators consistently deliver reliable and reproducible process results that are usually reserved for more costly systems. Another important aspect of the SolventVap is the safety features, which includes dry-run protection, water bath over-temperature shut-off protection, and fuse protection. Rotary evaporator features a specially designed motor and worm gear, which provides constant rotation at speeds from 10 to 180 rpm. As the flask containing the solvent is rotated, it continually transfers a thin layer of liquid over the entire inner surface. This gives a very large surface area for evaporation, which is caused by the gentle heating from the water bath. The rotating system is fitted with a special seal that allows the apparatus to be placed under vacuum, effectively reducing the boiling point of the solvents and removing the vapor phase, making the process much more efficient. Each unit is also equipped with an easy-to-use vacuum release and a continuous feed system, which allows solvent to be constantly drawn into the rotating flask without needing to stop the operation. Digital water bath operates from ambient temperature to 99°C (210°F) with PID temperature control stepping at 0.1°C increments. Heating coils are located directly inside the pan for the most efficient heating possible. A built-in overheat protector will shut down power, should the controller fail. Standard Glassware Set 0.13 gallon (0.5L), 0.26 gallon (1L) or 0.53 gallon (2 liters) pear shaped evaporating flask, 0.26 gallon (1 liter) round-bottomed receiving flask, and vertical cold trap condenser. Rotary evaporators with vertical condenser are great for distillation of solvents with higher boiling points. Features No chiller needed, utilizes dry ice for optimal efficiency. Solvent-resistant PTFE and Viton gaskets ensuring long time operation. Specialized motor with extremely compact, intermeshed worm and worm gear provides precise driving for very quiet, vibration-free operation. Downward-condensing vacuum connection design ensures safe vacuum operation. Modular design (individual rotary and water bath modules) for easy future upgrades. Easy multi-level manual lift with secure lock for the evaporating flask. Easy, straight-forward visual operation with digital speed and temperature display. PID temperature controller ensures accurate temperature control is maintained. One year warranty and lifetime US-based parts and service support Your safety is important to us! Please use caution when operating. Users of glass reaction equipment must take all necessary precautions to avoid contact with rotating parts, particularly entanglement of loose clothing, hair, necklaces, or other jewelry. Under these circumstances, the winding action of the rotating parts can draw the user(s) into the apparatus, resulting in breakage of glassware, burns, and/or chemical exposure. Extra caution must also be taken when operating with air-reactive materials, especially under vacuum. A leak can draw air into the apparatus and cause a violent reaction to occur. Specifications Electrical requirements 110V 60Hz single phase, 9.8A, 1075 watts (heater: 1050 watts, rotation motor: 25 watts) Evaporating flask Capacity: 0.13 gallon (0.5L), 0.26 gallon (1L) or 0.53 gallon (2L) Maximum load: Not to exceed 60% of the flask's capacity Rotation speed: 10 to 180 rpm Evaporating speed: 20 ml per minute Lifting: weight balancing manual control with lock Max lifting distance: 4 inches (extendable to 10 inches) Receiving flask 0.26 gallon (1L) Condenser Glassware: Vertical cold trap condenser with lid Vacuum connection: 3/8" hose barb x 1 Working environment 5 to 95°F Water bath Max. temp: 99° (210°F) Temp controller: digital Capacity: 2 gallons Material: stainless steel Dimensions: 10" diameter x 5" depth x 9.75" height Media: water Number of heaters: one Vacuum Connection: 3/8" hose barb x 1 (on condenser) Sealing: PTFE + Vinton gaskets Ultimate vacuum: < 3 torrs Safety Dry-run, over-temp shut-off, fuse protections Unit/shipping weight 21 / 40 Lb Unit/shipping dimensions 22 x 12.5 x 26" / 26 x 21 x 19" (WxDxH) Click here for specs for 110V WaterVac 0.7 cfm 735 torr 2-head recirculating water pump Standard package Part description Qty Part image Ai 110V WaterVac 0.7 cfm 735 torr 2-head recirculating water pump 1 pc Premium food grade silicone vacuum hose 6 ft 110V evaporator body 1 pc 110V water bath 1 pc Vertical cold trap condenser with 1 vacuum port and lid, glass 1 pc 0.13G/0.5L pear shaped evaporating flask, glass (choose based on volume of material to load) 1 pc 0.26G/1L pear shaped evaporating flask, glass (choose based on volume of material to load) 1 pc 0.26G/1L round shaped receiving flask, glass 1 pc Glass vapor duct with seal 1 set Material feeding tube with valve, glass 1 pc PTFE extension feeding hose 1 pc PTFE vacuum sealing kit 1 set Condenser cap kit 2 pcs Glass shaft cap and evaporator flask quick-release 2 pcs Condenser support and bracket 1 pc Condenser support securing screw 1 pc Receiving flask ball joint clamp 1 pc 3/8" vacuum connector x 1 1 pc 3-prong 110V US power cord for evaporator 1 pc Phillips screw driver 1 pc Mechanical vacuum gauge 1 pc User's manual 2 pcs
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
