Amag M2150 Elevator Controller System, US $1,000.00 – Picture 0

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 1

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 2

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 3

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 4

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 5

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 6

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 7

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 8

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 9

Amag M2150 Elevator Controller System, US $1,000.00 – Picture 10

Amag M2150 Elevator Controller System

US $1,000.00

Fort Washington, Maryland, United States
Mar 4th

Open on mobile:
QR code

***NO RETURNS ACCEPTED ON ELECTRONIC ITEM DUE TO ITS SENSITIVITY*** Specifications Operating Environment 32° F to 122° F (0°C to 50°C) 15% to 90% humidity, non-condensing AC Operation - 18 VAC Reader Supply 12 volts DC nominal Mounting Requirements The Symmetry multiNODE 2150 Elevator controller may be mounted on top of the elevator, or in the elevator equipment room. The enclosure provides two round and two keyhole mounting holes and knockouts for electrical connections. Communications Symmetry Elevator controllers can be interconnected in a chain configuration, using a 20mA current loop. The first controller in a chain can use the either the optional RS232 plug-in module to directly connect with a computer or dial-up modem or optional NIC plug-in module to connect via a TCP/IP network. Transmission Speed (Host Communications) Switch-selectable (9600/19200/38400 baud) Input/Output Terminations Barrier strips with screw clamp wire connections. Input Connections (Optional) A dry set of normally open contacts from each floor selection button is wired into the elevator controller in a matrix arrangement. If these inputs are provided, the controller only grants access to a validly selected floor. That floor number is included in the transaction report. If the inputs are not supplied, the controller enables access to all valid floors for a card holder. Access will be granted to any or all of the enabled floors. The corresponding transaction reports access is granted, but does not indicate the floor number. Storage Capacities 50,000 cards 47,000 off line stored events Configurations 1 Cab @ 64 floors each 2 Cab @ 32 floors each 4 Cab @ 16 floors each Reader Technologies and Card Formats The Symmetry multiNODE 2150 Elevator controller supports a range of reading technologies including magnetic stripe, proximity and smartcard by direct connection, and while a number of default card formats are pre-programmed as standard into the controller, there is the capability for custom formats to be defined. Output Connections Floor select relays provide the interface to the elevator control mechanism: one relay for each floor to be secured. Each floor may be secured (relay energized) or set to free access (relay de-energized), on an individual basis by commands from the client or by a timed command stored in the Symmetry multiNODE 2150 Elevator controller. Under total loss of power condition all relays revert to free access (relays de-energized) to provide fail safe operation. A fireman’s free access switch is also supported, which when operated removes power from all relays. Floor select relays are single Form C contact sets rated as: AC load @250 VAC-8 amps resistive, 6 amps inductive DC load @30 VDC-8 amps resistive, 4 amps inductive Maximum switching - 2000 VA/240 W resistive, 1500 VA/120 W, inductive Scheduled Commands Automatic timed commands are associated with a time code which defines the days of the week and the time intervals for each day during which a floor is to be either secured or set to free access. Communication Distances Symmetry multiNODE 2150 Elevator Node to PC/Modem (RS232) = 50ft/15m Symmetry multiNODE 2150 Elevator Node to other Symmetry multiNODE-2150 controllers (current loop) = 3000 ft/1000m Symmetry multiNODE 2150 Elevator Node to current loop reader = 3000ft/1000m

“This item is still a new and unused item with some signs of wear and tear from being moved around in storage. The item is missing all the original packaging and is not in the original packaging. Please refer to picture for minor wear and tear”

Brand	Amag Technology
MPN	M2150
Model	M2150
Country/Region of Manufacture	United States