US $140
| Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Country/Region of Manufacture | United States |
| Country of Manufacture | United States | ||
| Brand | COMPOUND ANGLE PLATE | ||
| USA AMERICAN TOOLMAKER MADE | precision ground finish as shown. |
Directions
Similar products from Supporting Blocks & Sets
2 MACHINIST MAGNETIC BRASS BLOCKS PRECISION TOOL DIE METAL WORKING LOT 2
1 MACHINIST BROWN&SHARP 124 MAGNETIC BRASS METAL BLOCK PRECISION TOOL DIE LOT 3
Newmac Hekus Quick-Set Hold-Down Block Set of two
(Lot of 2) Machinist Tool Right Angle Plates (8 x 5 x 4-1/2) Japan
MACHINIST TOOLS LATHE MILL Large Brown & Sharpe V Block for Set Up
MITUTOYO V BLOCKS SET OF 2 WITH CLAMPS NO 181-904 WORKHOLD GRINDING MACHINIST
RARE set Brown & Sharpe 750A (No. 1) V-Blocks and Clamps Set - Great Condition!
MACHINIST MILL LATHE TOOL Machinist Parallel Blocks in Hard Case
MACHINIST MILL LATHE Machinist 2 Large 2 4 6 Blocks Ground Hardened Hold Down
Pair Lufkin Rule Co. V-Blocks with Clamps
THOMSON SB-8 SHAFT SUPPORT BLOCKS for 0.500 SHAFT (USED) Qty. 4
Lufkin Pair Lufkin 4" Hold Downs Wedges 902C In Original Box Excellent Condition
MACHINIST TOOLS LATHE MILL 2 Machinist V Block s for Set Up Hold Down
Vintage Pair Of V - Blocks 1 Large & 1 Small No Clamps Nice
MACHINIST MILL LATHE NICE Ground Hardened Unusual V Block Set Up Hold Fixture
Vintage Brown And Sharpe Machist V-Block 749-1 Made In USA
MACHINIST 3"DIAMETER BY 1 7/16" THICK HEAVY STEEL BENCH BLOCK FOR DRIVING PINS
Starrett 271B Clamp, 1-1/4" Diameter Hold Capacity
Starrett 568A V-Block And Clamp For Round Or Square Work, 2" Diameter
People who viewed this item also vieved
IDEAL MORSE TAPER NO 3 7-008B ~ USED
#4 Morse Taper Dead Center Carbide Tipped
ROYAL PRODUCTS PN 11032 DEAD CENTER 4MT WITH CARBIDE TIP
6.0 Inch Diameter Magnetic Chuck on 5C Collet Adaptor
4 INCH JAW BORING RING (3900-4649)
8-1/4" BUCK FORKARDT 3 JAW SCROLLING LATHE CHUCK W/ L00 MOUNT
STAUFF TYPE GR.4 IV HYDRAULIC PIPE CONDUIT MOUNTING 1" Tube Twin Series Clamp
NEW Carr Lane Roemheld, Swing Clamp CLR-302-SCA
(2) Williams Agrippa 110 C-Clamp Short Spindle 6" to 10" Opening USED
LOT OF 7 SCHAUBLIN 8 MM COLLETS 3MM SIZES
Huth Clamp Collet, 2-3/8 inch HTH-1723 Lot of 2 set
LOT OF 7 SCHAUBLIN 8 MM COLLETS 2MM SIZES
HARDINGE C-27D 9" FACE PLATE, THREADED MOUNT
Enerpac Swing Clamp Cylinder RWR-300 NEW
Enerpac Hydraulic Cylinder Repair Kit RW3K1
Enerpac 4 Way Directional Control Valves VC-20 NEW
6" Vise Jaws Opens 8"+ Swivel Base Fit Bridgeports Mill
Snap Jaws Special Angle Vise Jaw Quickly Do Any Angle
6” ANGLE VISE W 2 WAY MOVEMENT TILT & SWIVEL~ONTARIO, CALIF.~
Cushman Super Spacer Mill Milling
HAAS HRT 210 T SLOT ROTARY TABLE 8" CNC SERVO
10 INCH HORIZONTAL/VERTICAL ROTARY TABLE - MADE IN TAIWAN 3900-2330)
HARDINGE 5C COLLET INDEXER TAILSTOCK BENCH CENTER SETUP SB-4 - HV-4N - T800
Collet 5C Collet Closer Block Set- SQUARE & HEX with Rings and Closer Attachment
5C COLLET CHUCK 4" with WRENCH & REVERSED JAWS machinist tools *K
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies