Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 0

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 1

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 2

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 3

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 4

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 5

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 6

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 7

Arduino IDE DIY Geiger Counter Kit w/LCD and SD Logger Shield; w/o GM Tube, US $570 – Picture 8

Arduino Ide Diy Geiger Counter Kit W/lcd And Sd Logger Shield; W/o Gm Tube

US $570

Jerusalem, israel, Israel
Feb 13th

Open on mobile:
QR code

Arduino IDE DIY Geiger Kit ver. 1.01 with SD Logger Shield Board RH-K-GK-1-L Unique project for soldering, sold not assembled! Free CR1220 3V battery included for RTC! We supply link to download all required source files from RH Electronics website, you'll need to solder main board and SD shield by yourself! If you need this item fully soldered please check my other items. This is unique hardware with open source code Geiger SD Logger project based on Arduino IDE. The kit includes main board with 16x2 LCD and SD Logger Shield. SD Shield has RTC circuit (real time clock), 3.3V level shifter for SD card, Buzzer and micro SD socket. Support connection of Adafruit GPS module or UART logging through RX TX pins. Files on SD card contains CPM readings for each data point, your local date and time, nmea geographical data and total absorbed dose. 400V high voltage for GM Tube produced with PWM. Microcontroller program correct high voltage if battery capacity is too low. The kit makes clicker sound similar to a “classic” Geiger counter sound. The project is education DIY Geiger kit with SD logger, mostly intended to measure and log ambient background radiation or low/moderate radiation levels up to 100uSv/h. Note: Geiger Tube, Enclosure, SD Card, Battery and TTL Module are not included in the purchase! This kit requires good soldering skills to solder SMD, additional TTL dongle for uploading firmware and ability to use Arduino IDE. Technical specifications: Geiger Tube Compatibility: GM Tubes with anode voltage 350-480V Arduino IDE compatible, easy to modify the program LCD 16x2 HD44780 (fixed properly over main board, no need to use wires) Two tact buttons for controlling the software Moving Average calculating algorithm Represent dose in uSv/h or uRn/h units UART logging with "Radiation Logger", require USB-TTL dongle Adafruit GPS module support SD Shield Board with RTC Absorbed dose, CPM, NMEA logging Smart Backlight Control Fast Bargraph on LCD Battery Indicator for Ni-MH Clock 24 hours format Supply Voltage: 5V DC or Battery Supply Current: 25mA without backlight Dimensions: 81(L) x 37(W) x 50(H) mm Shipping Weight: 250gr SKU: RH-K-GK-1-L Radiation SD Logger based on Atmega-328 and programmed with Arduino IDE. SD Shield has SMT parts that require good soldering skills! Atmega microcontroller comes with Arduino IDE bootloader, but you need to upload supplied sketches by yourself. The main benefit of this kit is SD Logger Shield. It support micro SD Cards with capacity 2Gb-8GB. Radiation data stored with 3 files. Each time you starting the counter, it will create a new log files and the older files stay safe on card. Up to 100 files can be created before you need to clear SD memory. LOG.CSV store CPM readings for each data point. The file can be opened with our "Radiation Logger" Windows application for building graph or with any csv editor. LOG.TXT store local date and time, CPM, aborbed dose accumulated since last minute and battery voltage. If GPS module connected, LOG.TXT will also store NMEA geographical data. DOSE.TXT file keeps only total lifetime absorbed dose. User manual describes an example how you can export nmea data to google map and add CPM readings to the map. The software and hardware where designed to produce tube high voltage with PWM technology. No additional IC's required, everything is controlled with software. By default it programmed to 450V-480V for SBM-20. You can make fine adjust through software calibration from 350V to 480V. If required, the kit can be adjusted for 500V-550V. The kit compatible with many popular Geiger tubes, such as SBM-20, SBM-19, SI-29BG, SI-180G, SBT-9, SBT-11, J305 and more 400V range tubes. Current radiation dose in uSv/h or uRn/h units represented on LCD with CPM (counts per minute) readings. You can switch between LCD units with pressing "down" button. If you press "up" button, it will shows clock for several seconds, like a digital watches. RTC needs 3V backup battery CR1220. Adafruit GPS module can be connected to RX TX pins and selected through sketch settings during firmware uploading. If no GPS presented, you can use RX TX pins for UART logging. CPM value logged through UART to our "Radiation Logger" Windows program. When connected to computer, the kit can be used as nuclear radiation monitoring station for local logs, radmon or xively. It possible to separate SD Shield from the Main Board if kit used only for UART logging. Fast bargraph on LCD for search mode represent CPS (count per second) measurement. The scale controlled through arduino sketch. The counter has smart LCD backlight controlling for saving battery. Backlight will light on when CPM value reach presetted alert threshold or if you press any button. Alert BL pin is combined with LCD backlight and can be connected to additional alert led or drive relay module. The kit produce clicker sound beeps similar to "classic" Geiger Counter sound. You can mute buzzer with jumper removed. If radiation level is high, the kit inform you with additional sound indication. Arduino software developer can modify default supplied sketch. Arduino sketch download link, all required libraries link and printed electrical circuit supplied to the buyer. Please download assembling manual with part list and soldering steps: DOWNLOAD User Manual PDF Radiation Logger Software (require UART TTL Module) this video demonstrate two models: RH-K-GK-1-A and RH-K-GK-1-L, please consider the sku number you purchase. This listing is for RH-K-GK-1-L Main Board Package include: 1x High Quality Manufactured PCB 1x Atmega-328 Microcontroller with bootloader 1x LCD Module 16x2 Green Color 1x CR1220 3V Battery for RTC 1x 100R ohm Resistor 1x 220R ohm Resistor 2x 1K ohm Resistor 3x 10K ohm Resistor 1x 4.7M ohm Resistor 1x 10K Potentiometer 1x 1K Potentiometer 4x 100nF Ceramic Capacitor 1x 300pF Ceramic Capacitor 2x 22pF Ceramic Capacitor 1x 10nF 1000V Ceramic Capacitor 3x 100uF Electrolytic Capacitor 1x 1N4937 Diode 1x LED 3mm 1x MPSA44 High Voltage Transistor 2x 2N3904 Transistor 1x 100uH Axial Inductor 1x 10mH Radial Inductor 1x 16.000 MHz Crystal 1x 28 Pin IC Socket 1x Slide Switch On/Off 2x Tact Switch Side Right Angle 1x Terminal Block 1x Battery Connector Set 2x 6 Pin Female Header 1x 6 Pin Male Header Right Angle 2x 6 Pin Male Header Long 2x Standoffs for LCD 4x Screws for LCD SD Shield Package Include: 1x High Quality Manufactured PCB 2x 2.2K Resistor SMD 1206 1x 10K Resistor SMD 1206 3x 100nF Capacitor SMD 1206 1x 10uF Capacitor SMD Tantalum 1x 100uF Electrolytic Capacitor 1x BC847 Transistor SMD SOT-23 1x LM1117 3.3V Regulator SMD SOT-223 1x DS1307 RTC SMD SOIC 8 1x 74HC4050 SMD SOIC 16 1x 32.768KHz Crystal 1x Micro SD Socket SMT 1x CR1220 Socket 2x 3 Pin Female Header Connector 1x 4 Pin Female Header Connector 1x 6 Pin Female Header Connector 1x Piezo Buzzer 1x Jumper Cup 4x Standoff for PCB 4x Screws for PCB The kit’s hardware needs 4.6V-5.4V to operate when it drawn 20mA without LCD backlight. There is several options for powering the kit, please consider the best for you. Battery indicator in software will work only with Ni-MH batteries. 1. 4x AA 1.2V Ni-MH rechargeable batteries, 1800mAh or higher. 2. 2x AA 1.5V Alkaline batteries with 5V step-up module. 3. 3.7V LiPO battery with 5V step-up module, 1000mAh or higher. 4. 5V DC regulated power supply for indoor. To our valued customers, please read purchase terms before you bid or buy! Technical issues and support: If you purchase this item you are agree that you have skills and tools to perform required DIY soldering (or de-soldering) and you know how to connect additional external components or modules. All project components should be installed and soldered in proper polarity with proper connectors. Any hardware/software modifications are not covered with warranty. If you have doubt it always better to ask for technical support before doing something. Please download and read carefully PDF user manual, product purchase terms. Almost all technical issues already described in the manual! If you have any technical issue with the product please contact us asap. Support provided by email or via eBay message. Please read support requirements here http://www.rhelectronics.net/store/support-request Please read carefully product title, description and include list. Any questions are welcome. If you received broken or defective parts please contact us first, because we can resolve this problem in best way. Handling time: 5 business days to process international orders required after receiving cleared payment. This does not include the number of business days the shipping service will take to deliver the item to you. We can upload a tracking number during handing time even before your package was transferred to logistic company for the delivery. Shipping: We dispatch your order during 1-3 business day and will upload a tracking number to eBay for USA buyers only. Take note, international shipping is more complicated and longer than domestic, that's why when you buy internationally it mean you are agree to wait for the package. For Economy International Delivery default stated time is 3-5 weeks. Some countries may take longer because of your country custom regulation rules or postal service. USA usually take 2-4 weeks; Europe 1-4 weeks; Australia 2-4 weeks; Germany 3-4 weeks; Israel 3-7 days; Russian Federation 4-8 weeks; All other countries 3-5 weeks default delivery time. Please contact us if you not received your package during 30 days. During checkout you can select available and preferred shipping method for you country. We offer Economy International Shipping and Priority International Express Delivery. If you cannot wait 30-35 days for the delivery please select faster and more expensive method in advance! We do not accept any claims for shipping time if you have chosen Economy Shipping! Economy Shipping mean we'll send your items with Registered Air Mail, but we cannot promise it will be fast, because it depends on post service, flights schedules, weather accidents, custom processing and other things that out of our control. Priority Express Delivery promise you'll receive the order much more faster, so make your decision about shipping method before you pay. Priority Mail available for USA, United Kingdom, Canada, Germany, Australia. Other countries can select EMS Express. Tracking: Take note, we ship through state export account and not from post office branch. This is the reason why your package is trackable only after it was sent abroad from Israel export and not at the date of collecting or at the date we uploaded a tracking number. Online tracking system in Israel displays information with big delays, post website provide tracking info for reference only several days after your item was sent abroad! Please be patient for the delivery and contact us if you have additional questions about shipping. Don't buy/bid if you are not ready to wait for the package during 3-5 weeks when you select Economy Shipping! Don't buy/bid if you make low DSR feedback because of shipping time or shipping price or just because of your custom import tax! Custom & Duty Fee: All international buyers are responsible to cover any possible custom fee or import tax that maybe applied at his/her country. We are obligated by export law of Israel to declare an order price as it was stated in your PayPal bill. German buyers, please remember when you buy that in Germany import custom rules require you to pay fee. We are not accept any claim because of your country custom regulation rules / delays / fee! Please contact your local custom office for more details about custom process and import tax. Returns: Accepted if you not started to solder/use device. In original package, including all components. During 14 days after you receive the package. Payment: Paypal only, or cash for local pickup. V.A.T. : If you live in Israel please take note, all buyers with DELIVERY ADDRESS WITHIN ISRAEL HAVE TO PAY 18% VAT! You'll be charged by separate paypal invoice. Refusing to pay tax will force us to cancel the order. Thank you for your positive feedback!

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	RH Electronics
Type	Dosimeters
Model	RH-K-GK-1-L
Country/Region of Manufacture	Israel
MPN	RH-K-GK-1-L