Atmel AVR Fundamental DevKit, US $35.00 – Picture 0

Atmel AVR Fundamental DevKit, US $35.00 – Picture 1

Atmel AVR Fundamental DevKit, US $35.00 – Picture 2

Atmel Avr Fundamental Devkit

US $35.00

Irvine, California, United States
Jan 29th

Open on mobile:
QR code

DESCRIPTION: This is a perfect development board for those who want to learn embedded systems and component level electronics. No need to worry about an operating system on top of your code. The chip is completely blank and will not run a single line of code unless you want it to. The chip will do exactly what you tell it to do… nothing more and nothing less. This development board is completely open-source. The full design schematic will be supplied for reference. This board is designed specifically for assembly language development. There are only 131 instructions native to this Atmel family of AVR microcontrollers. Most real-time systems are developed in assembly due to its speed and the ability to have full control of the hardware. Learning to program in the native assembly language of the chip will make a better embedded engineer. NOTE: This is not a programmer, must be purchased separately. The recommended programmer is ATMEL AVRISP MKII Programmer. FEATURES: · HIGH-PERFORMANCE, LOW-POWER ATMEL AVR 8-BIT MICROCONTROLLER · ADVANCED RISC ARCHITECTURE o 131 POWERFUL INSTRUCTIONS – MOST SINGLE CLOCK CYCLE EXECUTION o 32 X 8 GENERAL PURPOSE WORKING REGISTERS o FULLY STATIC OPERATION o UP TO 16 MIPS THROUGHPUT AT 16MHZ o ON-CHIP 2-CYCLE MULTIPLIER · HIGH ENDURANCE NON-VOLATILE MEMORY SEGMENTS o 16 KBYTES OF IN-SYSTEM SELF-PROGRAMMABLE FLASH PROGRAM MEMORY o 512 BYTES OF EEPROM o 1 KBYTES INTERNAL SRAM o WRITE/ERASE CYCLES: 10,000 FLASH/100,000 EEPROM o DATA RETENTION: 20 YEARS AT 85 DEGREE C / 100 YEARS AT 25 DEGREE C o OPTIONAL BOOT CODE SECTION WITH INDEPENDENT LOCK BITS IN-SYSTEM PROGRAMMING BY ON-CHIP BOOT PROGRAM TRUE READ-WHILE-WRITE OPERATION o PROGRAMMING LOCK FOR SOFTWARE SECURITY · JTAG (IEEE STD 1149.1 COMPLIANT) INTERFACE o BOUNDARY-SCAN CAPABILITIES ACCORDING TO THE JTAG STANDARD o EXTENSIVE ON-CHIP DEBUG SUPPORT o PROGRAMMING OF FLASH, EEPROM, FUSES, AND LOCK BITS THROUGH THE JTAG INTERFACE · PERIPHERAL FEATURES o TWO 8-BIT TIMER/COUNTERS WITH SEPARATE PRESCALERS AND COMPARE MODES o ONE 16-BIT TIMER/COUNTER WITH SEPARATE PRESCALER, COMPARE MODE AND CAPTURE MODE o REAL TIME COUNTER WITH SEPARATE OSCILLATOR o FOUR PWM CHANNELS o 8-CHANNEL, 10-BIT ADC § 8 SINGLE-ENDED CHANNELS § 2 DIFFERENTIAL CHANNELS WITH PROGRAMMABLE GAIN AT 1X, 10X, OR 200X o BYTE-ORIENTED TWO WIRE SERIAL INTERFACE o PROGRAMMABLE SERIAL USART o MASTER/SLAVE SPI SERIAL INTERFACE o PROGRAMMABLE WATCHDOG TIMER WITH SEPARATE ON-CHIP OSCILLATOR o ON-CHIP ANALOG COMPARATOR · SPECIAL MICROCONTROLLER FEATURES o POWER-ON RESET AND PROGRAMMABLE BROWN-OUT DETECTION o INTERNAL CALIBRATED RC OSCILLATOR o EXTERNAL AND INTERNAL INTERRUPT SOURCES o SIX SLEEP MODES: IDLE, ADC NOISE REDUCTION, POWER-SAVE, POWER-DOWN, STANDBY AND EXTENDED STANDBY · I/O AND PACKAGES o 32 PROGRAMMABLE I/O LINES o 40-PIN PDIP · OPERATING VOLTAGES o 2.7V – 5.5 V FOR ATMEGA16L o 4.5V – 5.5V FOR ATMEGA16 · SPEED GRADES o 0-8 MHZ FOR ATMEGA16L o 0-16 MHZ FOR ATMEGA16 · POWER CONSUMPTION @ 1 MHZ, 3V, AND 25 DEGREE C FOR ATMEGA16L o ACTIVE: 1.1Ma o IDLE MODE: 0.35Ma o POWER-DOWN MODE: < 1Ua WHAT MAKES THIS DIFFERENT: · ALL I/O PINS HAVE PROTECTION RESISTORS – PROTECTION RESISTORS MAY BE BYPASSED WITH REMOVAL OF JUMPERS · ALL I/O PINS BROUGHT OUT TO EASILY ACCESSIBLE HEADERS · 16 ON-BOARD LEDS FOR OUTPUT INDICATORS – TWO PORTS OF 8-BIT EACH · 8 ON-BOARD SWITCHES FOR DIGITAL INPUTS (WITH 10K PULL-UP RESITORS) · 5 VOLT REGULATOR · ICSP (IN CIRCUIT SERIAL PROGRAMMING) HEADERS – BOTH 6 PIN AND 10 PIN VERSION · ALL COMPONENTS ARE THROUGH HOLE FOR EASE OF PROBING SIGNALS AND COMPONENT REPLACEMENT · CIRCUIT BOARD IS SIZED APPROPRIATELY FOR TROUBLE SHOOTING AND DEVELOPMENT TESTING · ON BOARD RESET CIRCUIT · FULLY COMPATIBLE WITH ATMEL STUDIO IDE (INTEGRATED DEVELOPMENT ENVIRONMENT PACKAGE INCLUDES: · BOARD · DC Power Cable WILL NEED: · PROGRAMMER · DC POWER SUPPLY- 9 volt to 12 volt at 500Ma · ATMEL STUDIO INTEGRATED DEVELOPMENT ENVIRONMENT (software) RETURN POLICY Your satisfaction is our priority! In the case that you are not satisfied with your purchase, return the item within 14 days for a full refund of the purchase price. For your inconvenience we will grant you 10% off your next purchase with us. SHIPPING INFO All items will ship via USPS First Class in U.S., unless other services are requested. Product will ship next day upon purchase.

Condition:

New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...

Brand

Atmel