Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 0

Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 1

Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 2

Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 3

Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 4

Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 5

Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 6

Automatic creep feed Surface Grinder Magerle FPA-10-S4, US $28,000.00 – Picture 7

Automatic Creep Feed Surface Grinder Magerle Fpa-10-s4

US $28,000.00

Rockford, Illinois, United States
Jan 30th

Open on mobile:

Maegerle FPA-10-S4 creep feed surface grinding machine. This machine was in use at a working facility on a daily basis until they no longer needed it. In working order. Sold used as is. Freight and rigging to be paid by buyer. I believe the details of the machine are similar to the below. Rigging and shipping by buyer. Rigging at our facility will be about $500. Also below are some details on creep feed grinding: Creep-feed grinding Creep-feed grinding (CFG) was invented in Germany in the late 1950s by Edmund and Gerhard Lang. Unlike normal grinding, which is used primarily to finish surfaces, CFG is used for high rates of material removal, competing with milling and turning as a manufacturing process choice. Depths of cut of up to 6 mm (0.25 inches) are used along with low workpiece speed. Surfaces with a softer-grade resin bond are used to keep workpiece temperature low and an improved surface finish up to 1.6 micrometres Rmax With CFG it takes 117 sec to remove 1 in.3 of material, whereas precision grinding would take more than 200 sec to do the same. CFG has the disadvantage of a wheel that is constantly degrading, and requires high spindle power, 51 hp (38 kW), and is limited in the length of part it can machine.[2] To address the problem of wheel sharpness, continuous-dress creep-feed grinding (CDCF) was developed in the 1970s. It dresses the wheel constantly during machining, keeping it in a state of specified sharpness. It takes only 17 sec. to remove 1 in3 of material, a huge gain in productivity. 38 hp (28 kW) spindle power is required, and runs at low to conventional spindle speeds. The limit on part length was erased. NOTE INFORMATION BELOW MAY NOT BE 100% ACCURATE - EMAIL QUESTIONS Table length 1050mm Table width 240mm Grinding length 1000mm Grinding width 320mm Grinding height 365mm Creep feed facility. Execution: hydraulic with automatic cycle Max. distance from table to spindle-centreline 515mm Longitudinal travel (X-axis) 1130mm Transversal travel (y axis) 270mm Automatic cross-feed: stepless from 0.200 m/min up to 7.00 m/min Table speeds: stepless from 3.00 m/min up to 30.0 m/min Automatic vertical feed: from 0.0003mm up to 0.030mm Vertical rapid traverse: 0.30 m/min Diameter of grinding wheel: 300mm Width of the grinding wheel: 160mm Grinding wheel speeds: stepless from 660rpm up to 3340rpm Machine's weight about: 5800 kg Overall dimensions machine: Length: 2800mm Width: 1600mm Height: 2700mm

Condition:	Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections. ...	Brand	Magerle
Model	FPA-10-S4