BETTER PACK 333 VERSION , BEIGE IN COLOR, USED BUT IN GOOD CONDITION . THE 333 VERSION IS CONSIDERED ONE Of THE BEST GUMMED TAPE DISPENSERS MADE AND ALSO THE MOST POPULAR AND ALSO MOST IMPORTANT MADE IN THE USA THIS UNIT HAS BEEN SERVICED AND CLEANED, The Description below is from the Internet. BEST IN THE WORLD MOST POPULAR AS WELL The Better Pack 333 is a rugged, reliable, simple-to-use manual water-activated tape dispenser. (The Better Pack 333 is also known as a paper tape dispenser, gummed tape dispenser or gum tape machine etc.). The Better Pack 333 has 15 preset tape lengths measured in inches on a dial. This model includes a top heater accessory and it requires electricity. With the addition of heat, the water in the reservoir is not only warmed faster but optimizes the tape’s adhesive properties. The Better Pack 333 product line is the world's #1 selling manual water-activated tape dispenser in the industry. Applications • Sealing between 1 and 100 cartons per day/per 8hr shift • Chilly or cold carton sealing environments Features of the Better Pack 333 Benefits 15 preset tape lengths measured in inches on a clearly marked dial Simple to use operation Steel side frame construction Durable water brushes provide consistent, uniform adhesive wetting Effective sealing Superior mechanics and guillotine blade deliver clean, even cutting of reinforced and non-reinforced tape Reliable Only one strip of water-activated tape needed for secure, strong seal Cost-effective No electricity is needed to operate the tape dispenser Sustainable and Cost-effective You are looking at the most popular manual water activated tape dispenser in the world! Rugged steel side frames ensure long life. Hardened guillotine cutting blades eliminate tearing action found on competitive models. Water brush system ensures uniform wetting. Easy pull handle dispenses up to 30" (76cm); repeat strokes provide longer lengths. For nonreinforced or reinforced tape 1-1/2 to 3" (4-7cm) wide. Also available with an optional top heater that warms the water to activate the tape's adhesives, thereby optimizing the tape's integrity and bonding properties. Renowned for its durability and dependability, the BP333 is the industry's most popular manual machine. Features a unique design that is mechanically superior to all other machines in its class. Economically priced, this unit is perfect for any application on a light to medium-volume packing line. Without the need for electricity, the dispenser is easy to move from one packing line to another. Stainless Steel Model Also Available Developed and engineered in response to market demand, the most popular Better Pack 333 is now available with corrosion-resistant stainless steel construction. The Better Pack 333 S was specially developed for use in work areas where frequent cleaning is necessary, such as in food processing plants. Features: • Dispenses up to 30" (76 cm) of tape with one stroke - more with multiple strokes. • Variety of simple tape length settings. • Two water brushes for uniform wetting. • Guillotine sheer blades for clean cutting. • Rugged steel side-frame construction. • Large water reservoir. • Handles both reinforced and non-reinforced paper tapes- from 1 1/2" to 3" wide (4-7cm). • Mechanically superior design. • Without the need for electricity, dispenser is easily moved from one packing line to another. This item is 30 lbs., box dimensions: 13" x 10" x 19" KEEP READING, SOME VERY IMPORTANT INFO YOU SHOULD KNOW IF YOU ARE USING A WATER ACTIVATED GUMMED TAPE DISPENSER PREVENTIVE MAINTENANCE STATEMENT Gummed tape dispensers require minimal preventive maintenance and care. However, the gummed tape used in tape dispensers produces a "dust" that if not removed can reduce the performance of the unit. Minimal lubrication is required for the cutting blades. Oiling these blades lightly on a monthly basis will greatly extend the life and performance of the blades. Weekly washing of the water brushes will assure the most effective reactivation of the glue on the tape. On reinforced tape the glues are heavier, and during dispensing some of this glue wipes off on the brushes and runs into the water tank. If not washed out with warm water and mild soap weekly the glue will accumulate and reduce the effectiveness of the moistening system by clogging the water brush bristles. No repair should be attempted by well meaning but inexperienced persons. This could cause additional problems. We offer full repair services on most tape dispensers, or we will direct you to a knowledgeable source. SUGGESTED PREVENTIVE MAINTENANCE The following suggested preventive maintenance applies to all tape machine models in this web site: Weekly Wash water brushes with mild soap; rinse well. Wash water tank with mild soap; rinse well. Monthly Clean accumulated glue from blades. Apply light coating of light machine oil to back of blade (manuals). On 555 and E and R models, add few drops of oil to the blade felt pad. Semi-Annually Thoroughly clean all accumulated pieces of tape, tape dust and any other foreign material from inside of machine with dry brush or blower. Clean bottom of heaters and pressure plates of accumulated glue. Clean all covers with a damp rag. Trouble Shooting Instructions for Model BP 333 Most Common Malfunctions 1. Not Cutting A. Check and clean blades FM2OBXK, replace if dull B. Check for worn or broken spring FM48AX C. Check stationary shear adjustment 2. Not Feeding A. Check yoke spring adjustment FM33AX - Section 6 Page 4 B. Check gear assembly GE79X for missing or flattened teeth C. Check feed handle pawls (missing) K44B D. Check FM2OBX for accumulated grease or tape resins and clean E. Check set screw on feed wheel PW77CX F. Check FM12EL for binding (replace) 3. Jamming A. Check main gear GE79X for flattened or missing teeth. Replace. B. Check FM11X for bending (lower tape plate) C. Check for bent FM15 shaft D. Check FM12EL for binding E. Check for missing water brush PW1O7AK GENERAL TROUBLE SHOOTING INSTRUCTIONS Tape Feed Problems A) When pulling handle, feed wheel not gripping tape securely. Cause, incorrect adjustment of set screw on Cutter Yoke Assembly, FM26XXX. see Cutter Yoke adjustment. Tape Jams A) Shear Blade, FM2OBX, doesn't lift up before tape feed. See Cutter Yoke and Shear adjustment. B) Tape is being pinched by Pressure Plate due to worn moistening brushes. C) Upper Tape Plate, FM12EL, missing or not in correct position. D) Insufficient space between Pivot Rod, FM-15 and Lower Tape Plate, FM11X. Cutting Problems
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
