US $77
Condition | Used
:
An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
|
Seller Notes | “Vert good lightly used condition - 1 small chip on flute tip. See photos.” |
Directions
Similar products from End Mills Router & Drill Bits
Napoleon 8mm water slot cutter straight cutting edge elumatec, Federhenn, Rotox
Lot 1pcs 2Flute HSS-AL Ballnose End Mills R4 Cutting Dia 8mm Length 95mm
KEO .037" X .111" x 1/8"x 1-1/2 Miniature 2 FLUTE CARBIDE END MILL 83732 USA NEW
KEO 3/64" 3 FLUTE LONG REACH CARBIDE END MILL 87013-TiCN Coated USA NEW
3ea. 3/4" 2fl Carbide end mills
10ea. 3/8" 2fl Carbide end mills
10ea. 1/4" 4fl Carbide end mills
3ea. 3/4" 3fl Carbide end mills
29/32" (.9062") X 1-5/8" x 1" Shank 2 FLUTE Double End HSS END MILL New USA
Onsrud EMC600374 3/4" Carbide Endmill 6in, 8-Flute, TiCN
1 KEO 7/64" x 3/8" 2 FLUTE CARBIDE BALL Nose HP END MILL 83306-AD USA NEW .1093"
BRAND NEW 1 1/4" 4 FL HSS LONG END MILL W/ 3/4" SHANK POLAND FREE SHIPPING
Metal Removal Solid Carbide End Mill- USED 2"x2"x3 3/8"
CID Performance Tool HH Series 1/2" x 1/2" x 1 1/4" x 3", Solid Carbide End Mill
Destiny Tool (Viper) V348485, 3/4" x 3/4" x 3 1/2" x 6", Solid Carbide End Mill
Titan TC74184, 3/4" x 3/4" x 1 1/2" x 4" Solid Carbide Corner Radius End Mill
Interstate 01710243, 3/8" x 3/8" x 9/16" x 2 5/16" HSS, Square End Mill
OSG 455-6250, 5/8" x 5/8" x 1 1/4" x 3 1/2", Solid Carbide End Mill
SGS 31611, 7/32" x 1/4" x 7/16" x 2", Solid Carbide End Mill
Accupro 78958501, 0.0700" x 1/8" x 0.1050" x 1 1/2", Solid Carbide End Mill
People who viewed this item also vieved
GTN 3 IC328 ISCAR *** 10 INSERTS *** FACTORY PACK ***
WNMG 432 HT CR600 CERATIP INSERTS
NEW INVOLUTE GEAR CUTTER #4 40P 26-34T 14.5PA 7/8"bore HSS NTD&TCo.
NEW 74113601 SGS SINGLE FLUTE 1/2" CARBIDE COUNTERSINK 1/4 SHANK FREE SHIPPING
J&L 14-PC Over-Under Chucking Reamer Set - USA Made
NOS! National Twist Drill #8 TAPER PIN REAMER, 11/32" SQUARE DRIVE
Lot of 9 Dies - 1-4/5" Base Diameter - CPD F55
Lot of 10 Dies - 1-4/5" Base Diameter
STARRETT BAND SAW BLADE COIL STOCK FLEX BACK 3/4 X 032 X 3S / SKIP
Felker 12" Segmented Rim Wet Dry Diamond Blade masonry brick block paver Premium
NTK CERAMIC INSERTS SPG324 Z0525 PACK OF 10 **SALE**
KENNAMETAL CERAMIC INSERTS SPG438 RW4 GRADE KC850 PACK OF 7
duMont Broach Bushing 11mm-B 1-3/4 OAL
Shop Made Broach Bushing 30mm-B 2-1/4 OAL
Forney 60124 Tungsten Carbide Burr with 1/4-Inch Shank, Tree Radius, 1/4-Inch
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies