+ Post new Ad
Bullard Manual for 20-Speed Headstock, US $1500 – Picture 0
Bullard Manual for 20-Speed Headstock, US $1500 – Picture 0

Bullard Manual For 20-speed Headstock

US $1500

  • Holland, Netherlands
  • Oct 30th
Open on mobile:
QR code
           1. 36 pages Bullard TM-VTL020A, Technical Manual second edition. 20-speed Headstock Equipment with Hydraulic power pack utilized on Dyn-Au-tape and Dynatrol Vertical Turret Lathes Operations * Maintenance, This technical manual contains operating instruction, sequence of operation and maintenance instructions for the components of the 20-speed headstock equipped with hydraulic power pack. The headstock is utilized on both Dyn-Au-Tape and Dynatrol Vertical Turret Lathes.     All my Bullard items come of a distrubutor out of Rotterdam (The Netherlands) are full original or copy manuals from the manufacturer/distrubutor are unused, clean and no notes or underlining.                      Item wil be sent in an cardboard box. All books are complete and in good condition, unless otherwise stated. Minor defects (few annotations and underlinings, stamps, etc.) have not been mentioned in all cases.       TABLE OF CONTENTS Paragraph Title Page General                1 Speed Ranges     1 Speed Selection 6 Operation            11 Manual Mode Sequence of Operation         12. Jog Circuit Sequence of Operation                17 Jog Circuit Adjustments    17 Zero Speed Switch             21 Appendix A Table Speed Charts for Machine              A-l Sizes 26 through 124 inches LIST OF ILLUSTRATIONS Figure Title   Page Main Drive and Hydraulic Power    2 Package Components (2 sheets) Rear View of Headstock    6 Headstock Port Location  7 Headstock Shifter Schematic           8 Typical Headstock Speed Selector 11      Dial (switch) Electrical Schematic          14 Jog Circuit Hydraulic Schematic      18 Zero Speed Swith and Tachometer                22 Figure    Title Page 9            Zero Speed Switch Magnetic Pickup              24 10          Zero Speed and Tachometer Switch               25 Location and Troubleshooting (2 sheets) LIST OF TABLES Number            Title        Page Table Speed Limitations Chart         4 Input Shaft Speeds (REM) for Headstock      5 Table Drive Pinion/Gear Ratios used             5 with Headstock Energized Solenoid and Speed Number       9 Chart Headstock Table Speed Chart         10 Speed Number Ratio X Multiplier =               10 Table R.P.M.                 The actual shipping cost (to be determined based on your country) Cheapest shipping method is at buyer's risk via standard mail  or economy airmail (other destinations). Shipments can be registered, if buyer prefers. Costs depend of weight, priority and destination. I will inform you        

Directions

Similar products from Other Instruction Manuals

Mechanics Vest Pocket Reference Book by Wolfe & Phelps

Mechanics Vest Pocket Reference Book by Wolfe & Phelps

  • Allen, Texas, United States
  • Nov 1st
Lincoln Ranger 8 + Diesel Welder

Lincoln Ranger 8 + Diesel Welder

  • Simi Valley, California, United States
  • Nov 1st
1978 INDUSTRIAL METAL CUTTING MACHINE SHOP TOOLS CATALOG 'PTC' PENN TOOL CO.

1978 INDUSTRIAL METAL CUTTING MACHINE SHOP TOOLS CATALOG 'PTC' PENN TOOL CO.

  • Wichita, Kansas, United States
  • Nov 1st
1980 METAL INDUSTRIAL CATALOG CARB-O-LOCK TOOLHOLDERS, BORING BARS & CARTRIDGES

1980 METAL INDUSTRIAL CATALOG CARB-O-LOCK TOOLHOLDERS, BORING BARS & CARTRIDGES

  • Wichita, Kansas, United States
  • Nov 1st
GE Fanuc Automation I/O Unit Model A Power Mate A B C Series 0 15 16 18 Manual

GE Fanuc Automation I/O Unit Model A Power Mate A B C Series 0 15 16 18 Manual

  • Grand Rapids, Michigan, United States
  • Nov 1st
DoAll Surface Grinder VS-612 Parts Manual

DoAll Surface Grinder VS-612 Parts Manual

  • Mississauga, Ontario, Canada
  • Oct 31st
Hauser M-5 Jig Borer Instruction Manual

Hauser M-5 Jig Borer Instruction Manual

  • Mississauga, Ontario, Canada
  • Oct 31st
MORI SEIKI manual programming maual mori fanuc 6T manual

MORI SEIKI manual programming maual mori fanuc 6T manual

  • Hadley, Pennsylvania, United States
  • Oct 31st
Rockwell 14” Metal Cutting Lathe with Collet Closer

Rockwell 14” Metal Cutting Lathe with Collet Closer

  • Shelbyville, Illinois, United States
  • Oct 31st
Yale Service Manual 524164529 _ MPE/MPW 060-080E Electric lift truck forklift

Yale Service Manual 524164529 _ MPE/MPW 060-080E Electric lift truck forklift

  • Grand Rapids, Michigan, United States
  • Oct 31st
Bullard Process And Tool Layout Typical Transmiss

Bullard Process And Tool Layout Typical Transmiss

  • Holland, Netherlands
  • Oct 30th
Bullard Lubrication Manual Dyn-Au-Tape Vertical L

Bullard Lubrication Manual Dyn-Au-Tape Vertical L

  • Holland, Netherlands
  • Oct 30th
Bullard Advance Copy Two Range Headstock 4:1 D.C

Bullard Advance Copy Two Range Headstock 4:1 D.C

  • Holland, Netherlands
  • Oct 30th
Bullard Manual for Templa-Turn Templates

Bullard Manual for Templa-Turn Templates

  • Holland, Netherlands
  • Oct 30th
Bullard Operators Manual for Precision Vertical G

Bullard Operators Manual for Precision Vertical G

  • Holland, Netherlands
  • Oct 30th
VINTAGE ILLINOIS TOOL WORKS ILLINITE TRIGONOMETRY TABLES & FUNCTIONS BOOKLET

VINTAGE ILLINOIS TOOL WORKS ILLINITE TRIGONOMETRY TABLES & FUNCTIONS BOOKLET

  • Lakehurst, New Jersey, United States
  • Oct 29th
Budgit Portable Electric Hoists Operation and Service Manual Crane Budget

Budgit Portable Electric Hoists Operation and Service Manual Crane Budget

  • Kelso, Washington, United States
  • Oct 29th
Mazak Programming Mazatrol T Plus Manual #: H732PA0075E 4/6 Axis spec

Mazak Programming Mazatrol T Plus Manual #: H732PA0075E 4/6 Axis spec

  • Old Fort, North Carolina, United States
  • Oct 29th
Vintage 1967 Barber Colman Automatic Controls Service Manual Rockford, Il Ill

Vintage 1967 Barber Colman Automatic Controls Service Manual Rockford, Il Ill

  • Forreston, Illinois, United States
  • Oct 29th
VINTAGE 1942 MACHINERY'S HNADBOOK 11TH EDITION/THUMB CUTOUT INDEX

VINTAGE 1942 MACHINERY'S HNADBOOK 11TH EDITION/THUMB CUTOUT INDEX

  • Bowling Green, Ohio, United States
  • Oct 29th

People who viewed this item also vieved

Okuma CNC Systems OSP5020L, 5000L-G,500L-G, IGF-L3 OSP Operation Manual

Okuma CNC Systems OSP5020L, 5000L-G,500L-G, IGF-L3 OSP Operation Manual

  • Waterford, Wisconsin, United States
  • Jan 30th
Okuma CNC Drive Units BLII-D / VACII / VACIII Maintenance Manual

Okuma CNC Drive Units BLII-D / VACII / VACIII Maintenance Manual

  • Waterford, Wisconsin, United States
  • Jan 30th
Okuma CNC Systems, OSP5020L, 5000L-G, 500L-G Special Functions Manual NO. 1,2,3.

Okuma CNC Systems, OSP5020L, 5000L-G, 500L-G Special Functions Manual NO. 1,2,3.

  • Waterford, Wisconsin, United States
  • Jan 30th
Okuma CNC Systems, OSP5020M, OSP500M-G, Alarm and Error List, 3353-E-R3

Okuma CNC Systems, OSP5020M, OSP500M-G, Alarm and Error List, 3353-E-R3

  • Waterford, Wisconsin, United States
  • Jan 30th
Okuma CNC Lathe LB15 with OSP5000L-G Parts Book, Pub no KLE15-367-R2, 1989

Okuma CNC Lathe LB15 with OSP5000L-G Parts Book, Pub no KLE15-367-R2, 1989

  • Waterford, Wisconsin, United States
  • Jan 30th
MACHINERY'S HANDBOOK GUIDE 23 +Ready Reference +Antique Use of Tables& Formulas!

MACHINERY'S HANDBOOK GUIDE 23 +Ready Reference +Antique Use of Tables& Formulas!

  • Knoxville, Tennessee, United States
  • Jan 30th
BRIDGEPORT SERIES II R2E4 MAINTENANCE MANUAL NEW

BRIDGEPORT SERIES II R2E4 MAINTENANCE MANUAL NEW

  • Pittsfield, Massachusetts, United States
  • Jan 30th
Vintage Stiles-Herman Fender Roller English Wheel Metal Fabrication Pat. 1922

Vintage Stiles-Herman Fender Roller English Wheel Metal Fabrication Pat. 1922

  • Chillicothe, Ohio, United States
  • Jan 30th
OSP-E100L Operation Manual 1st Edition 4813-E

OSP-E100L Operation Manual 1st Edition 4813-E

  • Paullina, Iowa, United States
  • Jan 30th
Machinists 11/21A BUY NOW USA Solid Brass Drift

Machinists 11/21A BUY NOW USA Solid Brass Drift

  • Lutz, Florida, United States
  • Jan 30th

By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.

Accept All Cookies