US $60.00
Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Manufacturer | Nmtb |
Model | NMTB40-CC3.00-1000 | ||
Brand | Carboloy |
Directions
Similar products from Collet Chucks & Sets
ETM Collet Chuck Set (INCOMPLETE)
Precision ER20 MT2 M10 CNC Lathe Collet Chuck Holder
#K445 Kobayashi 3 Jaw Collet Chuck
5C COLLET CHUCK 4" with WRENCH & REVERSED JAWS machinist tools *K
Collet 5C Collet Closer Block Set- SQUARE & HEX with Rings and Closer Attachment
HARDINGE 5C COLLET INDEXER TAILSTOCK BENCH CENTER SETUP SB-4 - HV-4N - T800
KENNAMETAL/ERICKSON DA COLLET CHUCK SS100 DA201600 EXTENDED NOSE NEW!!!
?? Welch Super Collet Chuck - 5C - 9/32" - In Very Good Condition ??
Big Daishowa "NEW BABY CHUCK" ST32-NBS20-300
ER-16 7/8 X 4 INCH SHANK COLLET CHUCK (3900-7694) - MADE IN TAIWAN
ER-40 BT30 SPRING COLLET CHUCK (3900-7570)
AS-IS! 2 RICHMILL TENSION & COMPRESSION TAPPING CHUCKS w/ CAT40 SHANKS
Collet Fixture, Collet Chuck? Jacobs? Fixture 96-F1
#3 MORSE TAPER SHANK ER40 COLLET CHUCK 771
Dunham 5C-DS Dead-Stop Step Chuck
Dunham 5C-SCRB Step Chuck Replacement
Dunham RB2010 Replacement Body for CC2010 Expanding Body
ERICKSON, BT40BER32070M, Collet Chuck, 0.08- 0.81" Cap, Projection 2.760", /HV1/
People who viewed this item also vieved
Porst Bros. Chicago 19/64 Collet For Mill, lathe machine, Machinist tools
Porst Bros. Chicago 7/64 Collet For Mill, lathe machine, Machinist tools
1/2 x 2-5/8" Expanding Mandrel (Arbor) - Number 1 Morse Taper Shank - American
MACHINIST LATHE MILL NICE Ground & Hardened Set Up Block Fixture Tapped angle
MACHINIST LATHE MILL Ground & Hardened Set Up Hold Plate Fixture for Sherline
LOT OF TE-CO 40104 & ASSORTED MILLING CNC TABLE MACHINIST CLAMPS
3-1/4" TO 8" LENGTH ASSORTED MACHINIST CNC MILLING TABLE CLAMP BARS BOLTS
6" LMC MOdel 6ZA5-6-46-64 Chuck
KITAGAWA B-208 8" Chuck CNC Lathe, Spindle Nose A2-6, 3 Jaw for Haas SL ST 20 TL
KURT 6" VISE D60 ANGLOCK D-SERIES Made in U.S.A. *
Multi Axis 4 inch Cross Slide Machinist Drill Press Vice / Vise
Milling Machine Swivel Base Vise
TAFT PEIRCE PRECISION BENCH CENTER METROLOGY
Morse 2 Headstock Spindle for Sherline Lathes, Tool Steel - from LatheCity
NIKKEN 2MT LIVE CENTER STK 3040
Enerpac 4 Way Manual Air Valve VA - 4
Unusual Swivel Angle mounting plate for Milling Machine or other Machines
LATHE TOOL TURRET BLOCK CNC LOC1823
LATHE TOOL TURRET BLOCK CNC LOC1822
1 1/2 " ID LATHE TOOL TURRET BLOCK 84360 LOC1820
PRATT & WHITNEY 20” Horizontal Rotary Table
TROYKE 18” Horizontal Rotary Table
MACHINIST LATHE MILL Machinist Phase II 8" Horizontal Verticle Table for Mill
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies