Digitrak Sonde F5D 19/12 Fluid Pressure Transmitter F5 Locator Ditch Witch batt, US $2,399.00 – Picture 0

Digitrak Sonde F5D 19/12 Fluid Pressure Transmitter F5 Locator Ditch Witch batt, US $2,399.00 – Picture 1

Digitrak Sonde F5D 19/12 Fluid Pressure Transmitter F5 Locator Ditch Witch batt, US $2,399.00 – Picture 2

Digitrak Sonde F5D 19/12 Fluid Pressure Transmitter F5 Locator Ditch Witch batt, US $2,399.00 – Picture 3

Digitrak Sonde F5D 19/12 Fluid Pressure Transmitter F5 Locator Ditch Witch batt, US $2,399.00 – Picture 4

Digitrak Sonde F5d 19/12 Fluid Pressure Transmitter F5 Locator Ditch Witch Batt

US $2,399.00

Kissimmee, Florida, United States
Mar 10th

Open on mobile:
QR code

DigiTrak F5 Transmitters Overview This Listing Is For The Sonde Pictured It Is New Unused DigiTrak F5® transmitters are available in five unique frequencies for maximum interference reduction. Two single-frequency transmitters and two dual-frequency transmitters are offered, in addition to two dual-frequency fluid pressure transmitters (FPT). F5 transmitters work with F5 systems only. Part # Label Color Model/Type F5Dpx 19/12 Yellow FPT XR dual frequency F5Dp 12/1.3 Light Gray FPT dual frequency F5D 19/12 Light Blue HDT dual frequency F5D 12/1.3 Brown HDT dual frequency F5X 18 Magenta Single frequency F5X 8 Orange Single frequency All DigiTrak F5 transmitters provide pitch, depth, and roll readings, with 0.1% pitch sensitivity and roll data transmitted using a 24-position clock. DigiTrak F5 transmitters are battery powered and enter sleep mode after 15 minutes of inactivity. The F5 locating system is also compatible with F Series™ transmitters and 12-kHz DucTrak™ transmitters. F5 Fluid Pressure Transmitters The long-range DigiTrak F5 Fluid Pressure Transmitter (Model FPT) provides downhole fluid pressure monitoring up to 250 psi (1725 kPa). The drilling fluid pressure is measured through sensor ports located on the front end cap on either side of the index slot. The FPT is available in two dual-frequency configurations: 19.2 kHz/12 kHz and 12 kHz/1.3 kHz. These transmitters have light-green tubes and incorporate a new mechanical design, in addition to the fluid pressure sensors. The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was. With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm). Thus, the FPT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. If using a tooling adapter, however, the new design will require a different adapter. Also, the housings must allow fluid to flow to the sensor ports for measurement of the drilling fluid pressure. Part # F5Dpx 19/12 F5Dp 12/1.3 Depth Range 65 ft 19.8 m 65 ft 19.8 m Frequency 19.2 kHz or 12 kHz 12 kHz or 1.3 kHz Battery Type (hours awake/asleep) 2 C-cell alkaline (20/200), or 1 SuperCell (70/400), or 2 SAFT LSH14 (40/400) 2 C-cell alkaline (20/200), or 1 SuperCell (70/400), or 2 SAFT LSH14 (40/400) Maximum Temperature 220° F 104° C 220° F 104° C Length x Diameter 15 x 1.25 in. 38.1 x 3.175 cm 15 x 1.25 in. 38.1 x 3.175 cm Weight 1.65 lb 748 g 1.65 lb 748 g Housing RequirementsThe FPT is compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. However, the FPT requires a path for fluid to flow from the annulus around the housing to the four sensor ports in the front end cap; slots in the housing will satisfy this requirement. If the slots are epoxied, then a 0.125 in. (3 mm) diameter hole must be installed to allow fluid pressure to be measured by the FPT. Compatible housings have at least one slot, but DCI recommends three slots equally spaced around the circumference of the housing for optimal signal emission and maximum battery life. The slots must be at least 1/16 or 0.0625 in. (1.6 mm) wide. Slot position and length requirements are shown below; all slot length measurements should be taken from the inside of the housing. F5 Dual-Frequency Transmitters The F5 dual-frequency transmitters (Model HDT) come in two configurations: 19.2 kHz/12 kHz and 12 kHz/1.3 kHz. These transmitters have light-green tubes and incorporate the new mechanical design like that used for the fluid pressure transmitters. The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was. With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm). Thus, the HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. If using a tooling adapter, however, the new design will require a different adapter. Part # F5D 19/12 F5D 12/1.3 Depth Range 65 ft 19.8 m 65 ft 19.8 m Frequency 19.2 kHz or 12 kHz 12 kHz or 1.3 kHz Battery Type (hours awake/asleep) 2 C-cell alkaline (20/200), or 1 SuperCell (70/400), or 2 SAFT LSH14 (40/400) 2 C-cell alkaline (20/200), or 1 SuperCell (70/400), or 2 SAFT LSH14 (40/400) Maximum Temperature 220° F 104° C 220° F 104° C Length x Diameter 15 x 1.25 in. 38.1 3.175 cm 15 x 1.25 in. 38.1 x 3.175 cm Weight 1.7 lb 771 g 1.7 lb 771 g Housing RequirementsThe HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. The housings must have at least one slot, but DCI recommends three slots equally spaced around the circumference of the housing for optimal signal emission and maximum battery life. The slots must be at least 1/16 or 0.0625 in. (1.6 mm) wide. Slot position and length requirements are shown below; all slot length measurements should be taken from the inside of the housing. F5 Single-Frequency Transmitters DCI's F5 single-frequency transmitters have light green tubes and share the same dimensions as other DigiTrak transmitters. They come in two frequency designations: 18.5kHz and 8.4 kHz. These transmitters are only for use with the F5 locating system. Part # F5X 18 F5X 8 Depth Range 65 ft 19.8 m 65 ft 19.8 m Frequency 18.5 kHz 8.4 kHz Battery Type (hours awake/asleep) 2 C-cell alkaline (20/200), or 1 SuperCell (70/400), or 2 SAFT LSH14 (40/400) 2 C-cell alkaline (20/200), or 1 SuperCell (70/400), or 2 SAFT LSH14 (40/400) Maximum Temperature 220° F 104° C 220° F 104° C Length x Diameter 15 x 1.25 in. 38 x 3.175 cm 15 x 1.25 in. 38 x 3.175 cm Weight 1.4 lb 635 g 1.4 lb 635 g Housing RequirementsDCI's F5 single-frequency transmitters have the same design as earlier DigiTrak transmitter models and are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. The housings must have at least one slot, but DCI recommends three slots equally spaced around the circumference of the housing for optimal signal emission and maximum battery life. The slots must be at least 1/16 or 0.0625 in. (1.6 mm) wide. Slot position and length requirements are shown below; all slot length measurements should be taken from the inside of the housing.

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Digitrak
Country/Region of Manufacture	United States
Model	FXL 19.2 Ext. Long Range Transmitter