ScriptSetter® VR36 and VR45 Imagesetter Specifications Dimensions: Weight: Power requirements: Heat dissipation: Recording source: Spot size: Density uniformity: Repeatability: Available resolutions and imaging speed: Record image width: Output media: Take-up cassette: VR36 and VRL36: Basic engine: 24.5"W x 40.5"D x 17"H ( 622mm x 1029mm x 431mm) VR45 and VRL45: Basic engine: 28"W x 40.5"D x 17"H ( 711mm x 1029mm x 431mm) VR36 and VRL36: 142 lbs. (64 Kg) VR45 and VRL45: 150 lbs. (68 Kg) 115/230V (#10%), 3.0/1.5 amps, 50/60 Hz, single phase 1000 BTU/hr. maximum VRL:One10mWvisibleredlaserdiode(670nmrecordingwavelength) VR:One10mWinfraredlaserdiode(780nmrecordingwavelength) .001" (25 microns) Within .3D on 100% dot VR36 and VRL36: #.0015" (.04mm) typical over 14" x 18". VR45 and VRL45: #.0015" (.04mm) typical over 18" x 24". May vary according to media, media packaging and processing conditions. 2,540 dpi: 4.1"/min; 2,400 dpi: 4.4"/min; 2,032 dpi: 5.2"/min; 1,800 dpi: 5.8"/min; 1,524 dpi: 6.9“/min; 1,446 dpi: 7.3”min; 1,270 dpi: 8.3 "/min; 1,200 dpi: 8.7"/min; 1,016 dpi: 10.3"/min; 1,000 dpi: 10.5"/min. VR36 and VRL36: 14.147" (359.6mm); 14"(355mm); 12.175"(309.2mm); 12"(304.8mm); VR45 and VRL45: Up to 18.157" (461.2mm) Visible red sensitive film or IR sensitive film (polyester base), paper or plate material, .004" to .007" thick - emulsion in, rolled on 2" I.D. heavy duty core. Maximum outside diameter: 4.3" (109mm). Selectable adjustment for .004" or .007" media. Roll capacity up to 200' (60m), including the following standard widths: 18.1" (460mm) and 18" (457mm) - VR45 and VRL45; 14.0"(355mm), 12.2" (310mm), and 12" (305mm) - VR36, VRL36, VR45, and VRL45. Supply cassettes are darkroom loaded (green safety light); capacity one roll, available for following media widths: 18.1"/18" - VR45 and VRL45 only, 14” or 12.2”/12” - VR36, VRL36, VR45, and VRL45. Capacity 25ft (7.6m) film; 20ft (6.1m) paper; 7 mil plate material requires an on-line processor. ECRM RIP Specifications Power Mac configurations (confirm with dealer or ECRM customer service) Recommended PC Configuration fully dedicated PC: Note: Due to the wide variety of PC platforms, please consult with your dealer or ECRM before purchasing a PC RIP workstation. Network Interfaces: Features: System Components: System Fonts: Recommended Configuration: • Power Mac 9500/132 or 9500/120 • Macintosh system software 7.5 or higher • 72MB total RAM (minimum) • 1.0GB or larger SCSI II hard disk with 10ms (or faster) average seek time and 5MB/sec sustained data rate • Uses PelBox/SCSI adapter kit (required) • Intel Pentium (90 MHz minimum) • 32-bit PCI bus • Adaptec 2940 disk controller (Required; no substitutions) • 1.0 GB (minimum) fast (10MB/s) SCSI-2 hard disk with <10ms average seek time, 7200 RPM spindle speed • SVGA graphics card w/1MB RAM and SVGA monitor (800 x 600 x 16 colors recommended resolution) • SMC EtherCard Elite 16 network interface board • Adaptec EZ-SCSI 3.11 or higher Alternative Configuration: • Power Mac 8100/80 • Macintosh system software 7.1.2 or higher • 72MB total RAM (minimum) • 1.0GB or larger internal SCSI II hard disk with 10ms (or faster) average seek time and 5MB/sec sustained data rate • Available full length NuBus slot for PelBox Nubus interface kit, or uses PelBox/SCSI adapter kit • 64MB RAM (expandable to 128MB) w/256K RAM cache; refresh rates as recommended by system board manufacturer • Microsoft compatible mouse • Serial (Com port), parallel printer port • 3.5” floppy drive • Enhanced keyboard • MS-DOS 6.2 or higher • Windows for Workgroups 3.11 or higher Works as a Chooser-level print device on an EtherTalk network (both Macs and PCs), or prints files from a network spool folder. PCs require a network interface board (SMC EtherCard Elite 16 recommended). • Level 2 PostScript® - language compatible • Easy to use menus; RIP monitor provides status of jobs • Folder queuing prints all files from a specified folder or directory • Precision screens for moire-free color separations • Preview option allows you to quickly RIP a job to view on the computer screen • Built-in calibration; RIP can be calibrated on a stand-alone computer; Easy to use exposure test • Parallel page processing for fast, productive throughput • Option to store RIPed jobs as compressed files for fast re-imaging and multi-copy imaging • Film saving option automatically orients image on media • Media management feature provides input and output cassette film counting; image positioning for direct to plate applications • ECRM FM Screening option
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
