US $1000
Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
UPC | Does Not Apply |
Directions
Similar products from Fittings & Plates
Center For Bridgeport 12" or 15" Rotary Table
Bega 896A Light fixture anchorage kit
7 1/2" Square Compound Angle Adjustable SINE PLATE - Machinist/Tapped/Toolmaker
LUFKIN ADJUSTABLE PARALLELS SET 915 L 3/8" TO 2-1/2"
Angle Plate; Genuine Taft-Peirce; 8" x 5" x 4 1/2" UAS No. 192, Machinist tools
USA 8" X 12" T SLOT ADJUSTABLE ANGLE TABLE W/ ROTARY BASE
NICE EAGLE ROCK 5C PNEUMATIC CHUCK
PRECISION 5C COLLET INDEXING FIXTURE W/ 1/2" 5C COLLET
ELLIS UNIVERSAL DIVIDING HEAD W/ BUCK 5" 3 JAW CHUCK & 3 PLATES USA
7" x 7" x 2" Tall Steel Surface Plate, Machinist Setup Fixture Tool, 16 lbs
SUPER SPACER HARTFORD HEAD INDEXER 6 SLOT INDEX PLATE FOR 8" HEAD
SUPER SPACER HARTFORD HEAD INDEXER 12 SLOT INDEX PLATE FOR 8" HEAD
1 ANGLE PLATE & CUBE MACHINIST TOOLS * PRECISION ANGLE
Elephant ETTF-40CAT Toolholder Tightening Fixture
Suburban Tool SineMate Machinist Vise SV-337-S1 USA Made FAST DELIVERY
Vintage Stepped Angle Plate Tool Maker Made 2 7/8" X 3 1/2" X 3 7/8"
HARDINGE 2" OC LATHE STEP CHUCK CLOSER w/ 2-3/16"-10 TPI THREADED MOUNT
Surburan tool Angle plate 8" x 8" x 8" model PAW-080808 Sn/ Ground
People who viewed this item also vieved
TECO Step Block Kit, 1" Thick, 2 Blocks Each 40102, 40103, 40104, 30507 Clamps
MACHINIST TOOLS LATHE MILL Lot of Machinist Parallel and Other Blocks For Set Up
MACHINIST LATHE MILL Lot of Machinist Blocks Cutters Calipers Bearings Chuck Etc
Sundstrand Centers Capacity 12 X 48 without Risers: Inv 3515
5"/125mm 3-Jaw Lathe Chuck Plain Back x0.003" TIR w/ 2 Sets of Jaws, #0559-0112
Bison 12.5" 3-Jaw Self-Centering Lathe Chuck, Plain Back, Semi Steel Body !46D!
Morse Ttaper MT3-22 Face milling arbor adapter(A)
Irwin 2025102 Adjustable Iron C-Clamp-2-1/2X1-3/8 C-CLAMP
2 Large Used Vintage Machinists Parallel Camp Parts 6 inches long
Parallel Clamps, (2) Vintage Machinist / Toolmaker Parallel Clamps
Original Hardinge step OC Collet closer Chuck OC 2" Dia Thread mount
5C Collet Fixture Closer. Unknown Brand. Homemade Handle Tool#1
5C "TRU-SET" LATHE CHUCK - 1 1/2" x 8 TPI MOUNT
13/16" Warner & Swasey #5 Collet, 4669-1004 Nardco
1-13/64" Warner & Swasey #5-1A Collet, 471-1002 Nardco
Hardinge B20 Feed Finger Pads 1-1/4" Round
Large NOS Williams USA 1" Dr. 6 Pt. 2-5/16 Inch Deep Impact Socket No. 17-674
Large NOS Williams USA 1" Dr. 6 Pt. 2-3/8 Inch Deep Impact Socket No. 17-676
Manual 40 x 20 VMC Pallet Changer Side by Side with Pallets and Receiver
15" x 15' Troyke Model DMT-18 Cross Sliding Rotary Table, S/N 3597-8
15" x 15' Troyke Model DMT-18 Cross Sliding Rotary Table, S/N 3343-15
2-3/4 Inch Precision Universal Movement Vise
General Tools 92 Swivel Head Pin Vise
Table Bench Vise 3" Work Bench Clamp Swivel Rotated Vice Hobby Craft Repair Tool
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies