Hydrographics Dip Tank Kit Water Transfer Printing Film, Flames Dragons Hydrodip, US $2,699.00 – Picture 0

Hydrographics Dip Tank Kit Water Transfer Printing Film, Flames Dragons Hydrodip, US $2,699.00 – Picture 1

Hydrographics Dip Tank Kit Water Transfer Printing Film, Flames Dragons Hydrodip, US $2,699.00 – Picture 2

Hydrographics Dip Tank Kit Water Transfer Printing Film, Flames Dragons Hydrodip

US $2,699.00

Phoenix, Arizona, United States
Jan 30th

Open on mobile:
QR code

855-900-3477 This is the perfect tank for the beginner to small business looking to test out the hydrographics industry! ADDITIONAL HYDROGRAPHIC PATTERNS AVAILABLE CALL TO ORDER SPECIFIC PATTERNS WITH YOUR DIP KIT MADE IN THE USA | 5 YEAR WARRANTY PACKAGE INCLUDES: - 6 Meters of Hydrographic Film (20 ft) - HVLP Spray Gun Set – 3 Sprayguns * Primer gun with 1.8 tip * Top coat gun with 1.4 tip * Touch up gun with 1.0 tip - 1 Gallon Darth Vator Activator 4FT STAINLESS STEEL DIP TANK SPECIFICATIONS: Tank Dimensions: 50?L x 26?W x 24?D – 135 GAL Capacity Tank Material: GA14 – 304 Stainless Steel Electrical: 110V – 8FT Power Cord Film Guides: (2) Vertical Guides – (1) Horizontal Crossbar Optional Stand: Heavy Duty Steel Frame – Powder Coated / +$150.00 HEATING SYSTEM SPECS Tank comes equipped with (1) 110V 1500W Screw Plug Heater. The heater is mounted to the sidewall of the tank with a high temperature polypropylene fitting and a water tight seal grommet. The heater has a dial thermostat. The heater will cycle on & off, sustaining your water temperature at the target temperature setting on the thermostat. We also supply a Stainless Steel Dial Clip-On Thermometer that is mounted on the horizontal crossbar so that you can monitor your water temperature. (We can also install any type of heaters for any custom applications. We can install these styles and configurations of heaters: “Screw Plug” / Sidewall Mounted, “Bayonet” / Corner-Flange Mounted. We can also install heaters with any particular wattage and voltage specifications.) FILTRATION SYSTEM SPECS Tank comes equipped with a “Spray Bar Style” Filtration System. The Standard Spray Bar is constructed from 304 Stainless Steel Pipe with drilled jets. It is mounted on the inside of the tank with heavy duty clamps and Stainless Steel hardware. After you dip an item, the operator flips the toggle switch that is mounted on the heater housing on the side of the tank to turn on the pump. This will activate the filtration system and spray high pressure water from the spray bar jets to skim your contaminated water over to the opposite end of the tank. That water will cascade into the filter housing, pass through the media filter, and trap any excess film particles. This will clear your dip area of any residual film or activator within 1 minute. The filtered water will then flow back to your pump through the return line and will pass back through the spray bar assembly. The Filter Housing is constructed out of 14GA 304 Stainless Steel. It has a Flange Mounted design with fasteners for easy removal for cleaning; and also to utilize the additional space in the tank if needed. The media filter is an aluminum-foam mesh particle filter that is re-usable. To clean, you simply pry it out, backflow rinse wash, and place it back into the frame in the filter housing. (We can also install the spray bar externally for custom applications. With this design, the spray bar is fixed-mounted to the outside sidewall of the tank. We then install the swivel brass jets on the inside sidewall of the tank.) PUMP SPECS Tank comes equipped with a Heavy Duty Mag Drive Submersible Pump – 1000 GPH. The pump sits inside the filter housing and can also be used to drain the water in the tank. Simply remove the pump from the housing, place inside the dip area floor of the tank, and pump out your water in minutes. (We can also install any type of pump for custom applications (HP, GPM, Inlet/Outlet Dimensions, Voltage, RPM, etc.) We also provide dip tips and techniques after purchase by calling us toll free at 855-900-3477 BUY IT NOW and start hydro dipping for yourself, your friends, family, and future clients!

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Darth Vator Activator
Hydrographic Film Pattern	Flames, Skulls, Dragons
Model	Stainless Steel
Dip Kit	Dip Tank/Film/Activator/HVLP Spray Gun
Country/Region of Manufacture	United States