This is a listing for Pro Laser II Lidar. The unit is used but in working condition, comes with a stand and a case. Please see the pictures and ask questions to avoid unnecessary returns. OPERATION single-unit hand-held system optional window mount optional monopod/tripod mount supply voltage -- car battery HUD (Heads-Up Display) allows operator to view target, illuminated aim dot and target speed in one window. Instant On stationary operation only measures speed and range for on-coming and/or going traffic (also measures range of stationary objects) Target (moving) Acquisition Time (longer time required for slower targets) ProLaser II: 0.6 sec typical ProLaser: 0.3 sec for 60 mph target stopwatch mode (ProLaser II only) Operator measures (with ladar) distance between objects (stores distance in ladar memory), and pushes a button when a target passes each object (ladar calculates time between button pushes); ladar computes target speed from distance (known) divided by time (button pushes); and displays calculated target. Ladar does not transmit to calculate speed in this mode. CONTROLS Transmit / Lock display TRIGGER pressed -- transmitting TRIGGER released -- display locked speeds remains on display until next transmission Range Control -- set maximum range (5 foot increments) speeds displayed Speed Control -- set minimum speed to activate output signal (camera, etc.) -- indicates ladar set to measure traffic on-coming (+), going (-), or both directions () Speed Control and Test switches -- both switches (pushed simultaneously) sets the ladar to measure only traffic that is on-coming (TRGT APPR), going (TRGT RECD), or both directions (TRGT BOTH). Test Checks display LED segments, test memory, test accuracy, displays software version (VERS/X.XX), displays programmed units (mph/ft or kmh/m), indicates on HUD if programmed for speed or range (SPED/RANG) display (displays HELP if any test failed). If failure detected operation is inhibited and the rear panel displays FAIL/XXXX, where XXXX is a message code used by the factory. Stopwatch Mode (ProLaser II only) Operator inputs distance (300 to 4500 feet, 1 ft increments) between objects, and pushes a button when a target passes each object (ladar calculates time between button pushes); ladar computes target speed from distance (known) divided by time (button pushes). Calculated target speed displayed in target window, elapsed time (to tenths of a second) displayed in range window. Ladar does not transmit to calculate speed in this mode. Brightness -- adjust rear panel LEDs and HUD Volume control -- adjust aiming control tone On/Off (on handle) -- runs self-test (see 3 lines above) on power-up DISPLAYS / INDICATORS HUD 1/4 inch aim dot (no operator alignment adjustments) speed or range (depends on software installed) HELP in place of speed or range indicates status message on LEDs. -- Low Volt (supply voltage too low, operation inhibited) -- RFI (Radio Frequency Interference, operation inhibited) Target Speed Display (LEDs) 5 to 299 mph (8 to 480 kmh) displays minus (-) in front of speed for receding targets accuracy: +/- 1 mph (+/- 2 kmh) Target Range Display (LEDs) ProLaser II 20 to 2,000 feet (6 to 610 meters) accuracy: +/- 1 foot (+/-0.3 meters) ProLaser 50 to 2,000 feet (15 to 610 meters) accuracy: +/- 1.25 feet (+/-0.5 meters) Note, maximum range setting is 2,000 feet (MAXR), ladar still measures speed and/or range of objects up to 4,000 feet if the signal echo power is sufficient. Speaker no tone -- no target intermittent tone -- processing target constant tone -- processing and displaying target speed / range Indicators Transmitting Power On SPECIFICATIONS The unit is programmable, some specifications and features, such as speed/range in English or metric units (mph/ft or kmh/m) are a function of software version installed. Some software versions display range (instead of speed) on HUD. Target Acquisition Time (longer time required for slower targets) ProLaser II 0.6 sec typical ProLaser 0.3 sec for 60 mph target Sample Time 0.3 seconds (300 ms) Speed Range on-coming and going traffic 5 to 299 mph (8 to 480 kmh) Speed Accuracy +/-1 mph (+/- 2 kmh) Antenna single aperture Beamwidth 4 mrad (0.23 degrees) Wavelength approx. 904 nm supply voltage 10.8 to 16.5 Vdc (1.5 A max) environmental -22 to 140 degrees Fahrenheit (-30 to 60 degrees Celsius) 0 to 95 percent humidity (non-condensing) storage temperature -40 to 176 degrees Fahrenheit (-40 to 80 degrees Celsius) PHYSICAL height 10 in (25.4 cm) includes handle width 3.3 in ( 8.4 cm) length 11 in (27.9 cm) WEIGHT 4 lb., 4 oz. (1.9 kg) Data Output for still or video camera ProLaser II RS-232 serial port ProLaser speed, direction, range, error messages signals when preset speed/range met
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
