Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 0

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 1

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 2

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 3

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 4

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 5

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 6

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 7

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 8

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 9

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 10

Large Electromagnetic Solenoid Actuators 120VAC Continuous Duty Molded Coil Pull, US $16.99 – Picture 11

Large Electromagnetic Solenoid Actuators 120vac Continuous Duty Molded Coil Pull

US $16.99

Springfield, Tennessee, United States
Jan 29th

Open on mobile:
QR code

2776XD2A.1.11 New (unused factory pulls) Large Heavy Duty Dormeyer Electromagnetic Solenoid Actuators, 120VAC Continuous Duty Molded Coil, Pull Type Operation, Part Number 9002. Each bid quantity is for One (1) Actuator. You may bid / buy any number, up to the total quantity available above. Note: These appear to be new actuators that were installed on some kind of equipment and then removed. They show no evidence of actual use, however, there are screw marks where they were bolted down, as well as some scratches where the terminals were connected. They all look virtually the same, and we received them in the original factory trays, so we are guessing they were removed from new equipment at the factory. The minor handling scratches are consistent with such an operation. We warrant them to be fully functional and as described. These were purchased at an industrial liquidation earlier this year, and we received over 200 of them in the original factory trays. We repackaged them in heavy Ziploks. We do not have any specs, but they are heavy duty in every way. We experimented with one briefly, and found that the ram retracts with a very authoritative "snap" when power is applied. I am not exactly sure what the pulling force would be, but you want to be CERTAIN you don't get a finger behind the ram when the juice is turned on. They leave an impression in a block of pine, and would probably black a fingernail. The molded coil is rated for continuous operation, so there is no problem with overheating. The coils is probably fairly moisture resistant as well. The weight is about a pound and two ounces each. Should far outlast and outperform the cheap imported stuff. According to the calipers: Overall length (ram extended): 4.099" / 104.11 mm Overall length (ram retracted): 3.037" / 77.14 mm Stroke: 1.062" (1-1/16") / 26.97 mm Overall width, excluding terminals: 1.985" / 50.43 mm Overall height: 2.086" / 52.99 mm Ram assembly width: .736" / 18.70 mmRam assembly height: 1.743" / 44.27 mmRam yoke inside width (where the cotter key is): .573" / 14.57 mmRam yoke outside width (where the cotter key is): .729" / 18.52 mmRam yoke holes: .152" / 3.87 mmMounting base (L x W x Thickness): 2.501" x 1.804" x .066" (63.52 mm x 45.83 mm x 1.69 mm)Mounting screw slot width: .203" / 5.17 mmMounting screw slot pattern (center to center): 2.161" x 1.358" (54.89 mm x 34.51 mm) Terminal width: .186" (3/16") / 4.71 mm

Condition

New other (see details) :

A new, unused item with absolutely no signs of wear. The item may be missing the original packaging, or in the original packaging but not sealed. The item may be a factory second or a new, unused item with defects. See the seller’s listing for full details and description of any imperfections.

Seller Notes

“These appear to be new actuators that were installed on some kind of equipment and then removed. They show no evidence of actual use, however, there are screw marks where they were bolted down, as well as some scratches where the terminals were connected.  They all look virtually the same, and we received them in the original factory trays, so we are guessing they were removed from new equipment at the factory. The minor handling scratches are consistent with such an operation. We warrant them to be fully functional and as described.”