US $21.90
Condition: |
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details.
...
|
Material | HSS(M2) |
Flutes | 2-Flute | ||
End Type | Double End | ||
Cutting Dia | 22mm | ||
Model | HSS(M2) 2Flute End mill | ||
Shank Dia | 20mm |
Directions
Similar products from End Mills Router & Drill Bits
IMCO 5/16 Series 1850 Carbide End Mill 4 Flute Square 3" Long x 5/16" Diam NEW
Assortment of End Mills of various Small Fractional sizes ( 35-pcs) HSS See Desc
Milling- Drilling Radius cutting Tools 6-Pc’s H.S.S. V.G.U.C.
MORSE 25/32" inch, END MILL, HS, 3 Flute, Morse Taper, 5-1/4" inches long, USA
5 PCS OSG Double End Endmills 1/8" 2 Flute Ball Nose with 3/8" Shank HSS 5230100
1/2 COLBALT T-CENTER AND DOUBLE END MILL 4 FLUTE MADE IN THE USA
20pcs Carbide PCB End Mill Endmill Cutting Edge 1.5 mm 1.8mm for Precise Milling
KENNAMETAL SOLID CARBIDE ENDMILL D=3/8 Z=3 37DEG
5pcs - 1/4" Carbide Endmill 3 Flute Flat Bottom Regular TiAlN
10pcs 1/8" Carbide Endmill 4F Flat Bottom Regular
10pcs -1/4" Carbide Endmill 4 Flute Flat Bottom Long 1-1/8" length of cut TiAlN
3/16" Carbide Router Bit 2 Flute Spiral Upcut with 1/4" shank
Weldon End Mill Bit B68-HS 1" Shank 4 Flute Flutes A 32-7 Length 3 11/16"
Hanita High Speed Steel HSS 1" x 1" x 4" x 6-1/2" 2 Flute Square Single End Mill
COUNTERSINK SET MACHINIST SEVERANCE NO 27-41 4 PIECE STEEL CASE FRESHLY SHARP
1/4" Carbide Endmill 3 Flute 5 degree taper per side Ballnose 1/2" shank TiAlN
5pc 1/4" Carbide Endmill 2 Flute Flat Bottom Reg TiAlN
1/4" Carbide Endmill 4 Flute .015" Corner Radius Regular TiAlN
3/16" Carbide Endmill 4 Flute .030" Corner Radius Regular TiAlN
People who viewed this item also vieved
10pcs FREE SHIPPING SANDVIK 266RG-16UNO1A120M 1125 10pcs
Greenfield 3/8-16 Bottom Forming Tap TN 19873
BRAND NEW SOLID TWIST FLUTE COUNTERBORE FOR #5 SCREWS , 2 FLUTE
BRAND NEW SOLID TWIST FLUTE COUNTERBORE FOR #8 SCREWS , 3 FLUTE
MACHINIST REAMERS VINTAGE WOODEN BOX
SET OF 3 PRESS BRAKES FOR UP TO 20-TON SHOP PRESSES 4",8",10"
10" PRESS BRAKE FOR UP TO 20-TON SHOP PRESSES
NEW BIG LOT OF HSS BANDSAWS 12'X6" MORSE SIMONDS STARRETT
NEW BIG LOT OF HSS 12' BANDSAWS LENEX DIEMASTER
(100pcs) CNGA 433 T1 WG-300 Greenleaf Ceramic Insert
New 10 Pcs - DNGA 431 Ceramic Inserts Kyocera
6 Spline Gear Pull Broach 2.185" x 54-1/4 Long 2 Piece Set
6 Spline Gear Pull Broach 2" Finisher TBCO.
Unibor USP-1 Pilot Pin, Bright Finish, 1-Pack
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies