Lotos Ltp7000 Igbt 70 Amps Pilot Arc Plasma Cutter

US $2100

  • Sunnyvale, California, United States
  • Jan 30th
GENERAL OVERVIEW Make: LOTOS TECHNOLOGY Model: LTP7000 (5th Generation with improved HF board)  Type: 70A IGBT Pilot ARC Plasma Cutter Condition: BRAND NEW (In Sealed Factory Box) Status: IN STOCK (Ships in 2 Business Days) Features: 70A plasma cutter 200 to 240VAC,  Dual Frequency (50Hz/60Hz) Robust Infineon (By Siemens) IGBT Power Drive Matrix with Pilot arc Function integrated. Brand new yet double function tested and performance tuned prior to shipping PAPST cooling system from Germany Input Voltage: 200~240 VAC Input Power Frequency: 50 hz / 60 hz (Better performance under 60 hz) Insulation Grade: B Housing Protection Grade: IP21 Size: 19'' L  x 12'' W x 8'' H Weight: 53 lbs (60 lbs with box and footpedal) Certification: CE, CCC, CSA and ISO-9001 certification Power factor: 0.93 Power efficiency: 85% Accessories: 80amps Pilot Arc Plasma Torch (13') with wheel guider. 80amps 13 pcs Plasma cutting Consumables (including 3 pcs installed on the torch head) Air Filter/Regulator Ground Clamp & Cable (9' 8") Connections, (like Air Hose etc.) User Manual ABOUT LOTOS Since 2000 Lotos Technology introduced inverter technology in welding and cutting machines, Lotos' latest high frequency inverter technology utilizes V-MOSFETs along with PWM (Pulse Width Modulation) to deliver a far more constant, concentrated and precise current to the cutting surface. This technology has been substantially reduced in size and weight of Inverter Plasma Cutters. It helps you to easily achieve smooth, clean cuts of wide range of surfaces and material (e.g. stainless steel, alloy steel, brass, aluminum and other conductive material) with minimal heat input and without distortion of metal. Lotos plasma cutters are designed especially for those DIY (do-it-yourself) users, while fully accommodating the demands of professional operators. Operating Voltage: 208/220vac 50/60HZ Input Single Phase 70amp cut draws 45Amps 40amp cut draws 22.5Amps 230V No Load Voltage Cutting Specs: 1.35" Severance Cut, Maximum load 1.15" Maximum load 3/4" Normal Ideal use 3" Per minute @ 1.35" Steel (Severance Cut) 11" Per minute @ 1.125" Thick Steel 17" Per minute @ .8" Thick Steel High Frequency and Contact Start: High Frequency DC Plasma cuts thicker materials than standard DC plasma cutters. Power Specs: Power Factor 0.93 100% Duty cycle at 50amp cut 60% Duty cycle at 70amp cut Air requirements: 75psi @ 4.8cfm Dual Internal High Speed Cooling Fans to Regulate Temperature and cool this unit. LTP7000 has built in Thermal & Overload Protection   CONTROL PANEL Accessories (Click to view FULL size image) Unrivaled Quality The production process for Lotos products is among the most stringent in the world and meets or exceeds some of the industry's most rigid standards. Our studies show that it is in fact among one of the best in the industry and is unrivaled by other would-be competitors. The quality of each of the integrated components is constantly monitored during the course of production. Only components and materials that meet the highest industry standards for quality are permitted to be incorporated into LOTOS products. Finally, upon conclusion of production, each unit is put through a newly devised, far more rigorous 30 point testing and quality inspection routine. This process is critical to ensuring a product that is not only safe, but reliable in both performance and durability. Cut at 12 Times the Speed of Sound Plasma cutting is a process that is used to cut steel and other metals using a plasma torch. In this process, an inert gas (compressed air) is blown at high speed out of a nozzle; at the same time an electrical arc is formed through that gas from the nozzle to the surface that is being cut, turning some of that gas to plasma. The plasma is sufficiently hot to melt the metal being cut and moves sufficiently fast to blow molten metal away from the cut. The plasma, which is maintained between the work-piece and electrode, travels at over 9000 MILES PER HOUR (15,000 km/Handle).  That’s over twelve times the speed of sound. Advantage of Plasma vs. Oxy-Fuel Torch Plasma does not use expensive, hazardous gases, only compressed air. It imparts much less heat into the piece being cut, eliminating warping. It does not require ignition. It leaves little to no slag to clean up or grind off.  The cost per cutting hour can be less than oxy-fuel since there is no gas cost. It is also much quicker and easier.  So, you cut better, faster and inexpensively. Skill and Training There is not a lot of skill or training required to operate a plasma cutter.  The torch should remain at a 90-degree angle.  With the Lotos LTP7000 you can keep a standoff or drag the tip of the torch on the metal. ADVANCED INVERTER TECHNOLOGY The LTP7000 inverter rectifies the input voltage (220VAC) into DC (Direct Current), which is then fed into a series of IGBTs. LOTOS LTP7000 utilizes the most advanced Infineon (By Siemens) Technology. These IGBT components are switched at thousands of Hertz, which greatly reduces the magnetic flux, and therefore the size of the transformer. Hence, the use of IGBTs allows for a compact and light weight machine such as the LTP7000 to operate at its performance parameters. In simple terms the use of these IGBTs makes it possible for LTP7000 to produce the necessary power, using very little space and creating minimal heat dissipation. Payment We accept Paypal, Credit cards (Visa/Master/Discover/American Express), Money Order or Checks. Please contact us if you have any questions. International customers, please contact us for shipping fees. Shipping and Tracking FREE FedEx shipping with FREE tracking information to 48 states. WARRANTY, SERVICE and PARTS Warranty Terms: Lotos Technology warrants that all equipment sold by our company, unless otherwise specifically stated, will be free from defects in materials and workmanship for a period of 1 year from date of shipment. Such warranty shall not apply in any event to failure or defects in materials due to normal wear and tear, failure to perform recommended or customary maintenance procedures, exposure to detrimental elements, improper storage, or corrosion, and shall not extend to any person or entity other than the customer. To purchase an extra 3 years' warranty, please click here.   Return: After shipment, product is returnable for a refund within 30 days of shipment, with a minimum 20% restocking fee. Lotos Technolgoy reserves the right to charge a restocking fee higher than 20% based on the condition of products received. Original shipping and handling fee is not refundable. Feel free to contact us if you have any questions or comments.
Condition:
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...
Brand LOTOS
Country/Region of Manufacture China
Model LTP7000

Directions

Similar products from Plasma Cutting Equipment

People who viewed this item also vieved

By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.

Accept All Cookies