Micro Effects 2X Red LED Lights & splitter & Control Flash Dim Blink 9V MEL MED, US $11.99 – Picture 0

Micro Effects 2X Red LED Lights & splitter & Control Flash Dim Blink 9V MEL MED, US $11.99 – Picture 1

Micro Effects 2X Red LED Lights & splitter & Control Flash Dim Blink 9V MEL MED, US $11.99 – Picture 2

Micro Effects 2X Red LED Lights & splitter & Control Flash Dim Blink 9V MEL MED, US $11.99 – Picture 3

Micro Effects 2X Red LED Lights & splitter & Control Flash Dim Blink 9V MEL MED, US $11.99 – Picture 4

Micro Effects 2X Red LED Lights & splitter & Control Flash Dim Blink 9V MEL MED, US $11.99 – Picture 5

Micro Effects 2X Red LED Lights & splitter & Control Flash Dim Blink 9V MEL MED, US $11.99 – Picture 6

Micro Effects 2x Red Led Lights & Splitter & Control Flash Dim Blink 9v Mel Med

US $11.99

Palmdale, California, United States
Jan 29th

Open on mobile:
QR code

2 pcs MEL-PB1 Micro Effects Light - Pure RED LED DC barrel connector light 1 pc MED1 Micro Effects Dimmer Control 1 pcs 2-Way Splitter Cable 1 pc 9 volt battery clip DC barrel type ***Battery Not Included *** *** see our eBay Store for other MEL Micro Effects Light items under MEL category *** The J2 LED Lighting, LLC P/N MED1 Micro Effects Dimmer provides dimming, multimode effects, and on / off control of 5 – 24 volt DC LED lights. The unit features a simple tactile three button interface; mode, speed, and light. The variety of effects combined with the simplicity of use makes this a great control for low complexity projects. The MED1 has eight dynamic effect modes and ten speed levels. The light button is used to switch the unit to standard static dimming. In the static dimming mode the speed button provides ten brightness steps. The speed button is also used to turn the unit off when it is held more than 1 second. Any button can be used to turn the unit back on. Mode effects patterns: 1) Up / Down varying brightness – always on 2) Strobe – fast 3) Blinking – long on 4) Blinking – long off 5) Flash - burst of pulses (emergency vehicle light) 6) Strobe – slow (beacon light) 7) Up / Down – flame flicker – always on 8) Up / Down – ramp up on ramp down off - repeat The MED1 operates with 5, 9, 12 or 24 volt DC lighting systems and can switch a maximum of 4 amps. The unit provides up to 20 watts of lighting control when using a 5 volt system, 48 watts on 12 volt or up to 96 watts of lighting on a 24 volt system. The control may be operated from a 9 volt battery for portable applications, it is recommended to limit the LED light load current to 100ma for battery life. The MED1 is equipped with a barrel connector type DC power jack and plug. The connectors are of the 5.5mm x 2.1mm size with a positive center connection. The MED1 is compatible with other J2 LED Lighting accessories of the same connector type. The body of the MED1 control is of a small size with a low profile. The MED1 body measures a nominal 1.4” length, 0.6” wide and 0.2” thickness. Each of the connector cables extends from the body 5.5”. The overall end to end length of the entire body and cable assembly is 13.0” Max. The unit’s body is sleeved in black and the cables are molded in black PVC. Well suited for various LED lighting applications such as: Flex Strip accent lighting Promotional LED signs Specialized decor lighting F/X prop and costume lighting Stage Lighting Theatrical effects lighting POS Point Of Sale displays Architectural accent lighting See the spec sheet in the photos for more details. MEL Light Specs: The J2 LED Lighting, LLC MEL (Micro Effects Light) is a series of simple low cost LED light sources with a built in DC barrel type connector. The 2.1 x 5.5mm barrel connector is very common for many low voltage DC power applications simplifying the building of a micro effects lighting system in a modular fashion. The MEL operates from 9 – 12 volts DC which allows a simple effects system operating from a 9 volt battery possible. More complex systems with numerous micro effects lights are possible from a 12 volt DC power source. Lighting systems can range from a single MEL to over 100 MELs depending on the complexity of a lighting project. The MEL is optimized for high light output at 9 volts DC with a nominal power of 0.18 watts operating at 20ma ref. With an input of 12 volts, a power consumption of 0.34 watts is typical, operating at 28ma ref. With input higher than 12 volts there is a diminishing light output due to thermal loading of the LED. The MEL is dimmable by either PWM (Pulse Width Modulation) type dimmers or with variable voltage input from 7 – 12 volts DC. The MEL can be made with pure fully saturated LED colors and with phosphor converted colors for a wide color gamut. The LED lens is water clear with a 30 degree output angle for a narrow beam. The MEL may be operated from a 9 volt battery for portable applications. When using a 9 volt battery it is recommended that the number of MELs does not exceed six in order to limit the load current to about 120ma for battery life. The MEL is equipped with a barrel connector type DC power jack to mate with a plug of the same type. The MEL uses a positive center power connection. The MEL is compatible with other J2 LED Lighting accessories of the same connector type which include two and three way DC barrel connector splitter cable harnesses, pigtail harnesses, MED1 Micro Effects Dimmers, 9 volt DC barrel battery clips, and DC barrel-to-wire terminal block adapters. The axial body of the MEL LED is of a small size and molded in black ABS resin. The MEL body overall length is 1.42” (36mm) and the diameter is 0.48” (12.2mm) nominal. Well suited for various LED lighting applications such as: Scenery / Props / Models / Animatronics / Robotics Fx- Special effects / costumes Theatrical stage and set obstruction marking Theming, decor lighting and promotion display products Amusement, arcade, gaming and entertainment lighting Specialty miniature accent lighting, micro fixtures, micro ceiling drop pendant lighting Sales and trade show displays and signage If you need to connect to wires the below terminal block adapters can be used: Adapter Connectors for Power

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	J2 LED Lighting, LLC
Country/Region of Manufacture	China
Model	MEL
9 volt battery operated	RED LEDs
MPN	MEL-PR1 2-Way Med-1