New Lot Of 3 Pcs. Blue Monster 70886 3/4" X 1429" Thread Seal Tape

US $19.99

Butner, North Carolina, United States
Aug 11th

Open on mobile:
QR code

New Lot of 3 PCS. Blue Monster 70886 3/4" x 1429" Thread Seal Tape Blue Monster PTFE Thread Seal Tape is a thicker, denser, general-purpose thread seal tape that comes in a monstrous 1,429" roll. That’s 5 times more tape than conventional rolls of low-density thin tapes. Fewer wraps are necessary to affect a leak-proof seal and it applies easily. No waste and no re-taping make sealing joints a breeze. Blue Monster thread sealing tape is manufactured from PTFE resin, a polymer consisting of recurring tetrafluoroethylene monomers whose formula is (CF2-CF2)n. It is inert and compatible with a very wide range of materials. Use Blue Monster on threads made from galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, polypropylene, PVC, CPVC, ABS, fiberglass and more. It can be used on pipes carrying the following: Acids, concentrated (see precautions) and Acids, dilute Alcohols, Gasohol Aliphatic solvents, Aromatic solvents, Chlorinated solvents Ammonia, liquid Caustics, concentrated (see precautions) Compressed air, Steam, Water Cutting oils Diesel fuel oil Ethylene glycol, Glycerine Fatty acids Heating oils, Kerosene Hydraulic fluids, Hydraulic oils Hydrogen, gaseous and liquid, Inert gases, gaseous and liquid Jet fuel Ketones, Petroleum solvents Liquid Petroleum Gas, Natural gas Mineral oils, Vegetable oils Nitrogen, gaseous and liquid Soap, liquid Specifications: Composition: 99.6% PTFE < 0.4% Pigment Color: Blue Length: 1429" Thickness: 0.0035" +/- 10% Density: 0.8g/cm3 Elongation: >100% Tensile Strength: 15N / mm2 Temperature Range: -450°F to +500°F (-268°C to +260°C) PTFE is completely stable up to +500o F or +260°C. Decomposition is slow up to 750°F or 400°C. Although decomposition will occur on contact with naked flames. Pressure rating: Mill-Rose Blue Monster Thread Sealing Tape has been used to seal fittings carrying water and oil at pressures up to 10,000 PSI or 69,000kPa Note: Pressure ratings are relative to the quality and torque of the fittings and the amount of tape used. Precautions Note: Keep Mill-Rose Blue Monster Thread Sealing Tape clean. Replace the clip on the spool after use. Store in a clean place. PTFE is virtually chemically resistant to all media, however there are a few exceptions. Alkali metals such as elemental sodium, potassium and lithium are to be avoided. These alkali metals remove fluorine from the polymer molecule. Extremely potent oxidizers such as fluorine (F2) and related compounds (e.g., chlorine trifluoride(CIF3) can be handled by PTFE, but only with great care. Since fluorine is absorbed into the resin, the mixture becomes sensitive to a source of ignition such as impact. Other media to avoid are 80% NaOH or KOH, metal hydrides such as boranes (e.g., B2H6), aluminum chloride, ammonia (NH3), certain amines (R-NH2), imines (R-NH) and 70% nitric acid at temperatures near the suggested service level. Do not use Mill-Rose Blue Monster Thread Sealing Tape on oxygen lines! Mill-Rose recommends Green Oxygen Tape for oxygen lines. For further safety details consult the Material Safety Data Sheet. Note: Mill-Rose also offers a Yellow Gas Line Tape where certain codes require it. Limited Liability: The information presented is in good faith, but no warranty is given nor are the results guaranteed. Since we have no control over the physical conditions surrounding the application of information herein contained, Mill-Rose disclaims any liability for untoward results. *** PRODUCT RECOVERY MANAGEMENT INC. IS REGISTERED IN AND IS THEREFORE REQUIRED TO COLLECT SALES TAX IN THE FOLLOWING STATES: FL, NC, NY, VA, & WY*** LEGAL DISCLAIMER: IN NO CASE SHALL PRODUCT RECOVERY MANAGEMENT, INC. (PRM), OUR DIRECTORS, OFFICERS, EMPLOYEES, AFFILIATES, AGENTS, CONTRACTORS, INTERNS, SUPPLIERS, SERVICE PROVIDERS OR LICENSORS BE LIABLE FOR ANY INJURY, LOSS, CLAIM, OR ANY DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND, INCLUDING, WITHOUT LIMITATION, LOST PROFITS, LOST REVENUE, LOST SAVINGS, LOSS OF DATA, REPLACEMENT COSTS, OR ANY SIMILAR DAMAGES, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, ARISING FROM YOUR USE OF ANY OF THE SERVICE OR ANY PRODUCTS PROCURED USING THE SERVICE, OR FOR ANY OTHER CLAIM RELATED IN ANY WAY TO YOUR USE OF THE SERVICE OR ANY PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY ERRORS OR OMISSIONS IN ANY CONTENT, OR ANY LOSS OR DAMAGE OF ANY KIND INCURRED AS A RESULT OF THE USE OF THE SERVICE OR ANY CONTENT (OR PRODUCT) POSTED, TRANSMITTED, OR OTHERWISE MADE AVAILABLE VIA THE SERVICE.

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	MPN	70886
Composition	99.6% PTFE & < 0.4% Pigment
Model	70886
Color	Blue
Thickness	0.0035" +/- 10%
Pressure rating	10,000 PSI or 69,000kPa
Density	0.8g/cm3
Temperature range	-450°F to +500°F (-268°C to +260°C)
Elongation	>100%
Tensile strength	15N / mm2
Brand	Mill-Rose
UPC	0038091708864