Radoincs D7412G Panel with 2 Bosch Expanders and Alarm Cotrol Progammable Timer, US $75.00 – Picture 0

Radoincs D7412G Panel with 2 Bosch Expanders and Alarm Cotrol Progammable Timer, US $75.00 – Picture 1

Radoincs D7412G Panel with 2 Bosch Expanders and Alarm Cotrol Progammable Timer, US $75.00 – Picture 2

Radoincs D7412G Panel with 2 Bosch Expanders and Alarm Cotrol Progammable Timer, US $75.00 – Picture 3

Radoincs D7412G Panel with 2 Bosch Expanders and Alarm Cotrol Progammable Timer, US $75.00 – Picture 4

Radoincs D7412g Panel With 2 Bosch Expanders And Alarm Cotrol Progammable Timer

US $75.00

San Antonio, Texas, United States
Jan 30th

Open on mobile:
QR code

Radonics D7412G- SpecificationsPrimary: 16.5 VAC 40 VA class 2 plug-in Transformer (D1640) Voltage Input (Power Supply)Secondary: Sealed lead-acid rechargeable (12 VDC, 7 Ah or 12 VDC, 17.2 or 18 Ah) battery. The panel supports a maximum of two 12 VDC, 7 Ah batteries using the D122 Dual Battery Harness or two D1218 (12 VDC, 17.2 or 18Ah) batteries using a D122.Current RequirementsPanel : 500 mA alarm, 200 mA idleSee the Standby Battery and Current Rating Chart for the current draw requirements of other system components.All external connections are inherently power-limited except battery terminals.Continuous PowerOutputs1.4 A maximum at 10.2 VDC to 13.9 VDC (continuous supply) total for all devices and outputs supplied at Terminals 3, 24, and 32 and at the Accessory and Programming Connectors.Alarm PowerOutput 2.0 A maximum at 10.2 VDC to 13.9 VDC output. Output may be steady or one of three pulsed patterns depending on programming. Switched AuxPower 1.4 A maximum at 10.2 VDC to 13.9 VDC output. Continuous output is interrupted by Sensor Reset or alarm verificationdepending on programming. Power OutputsFire andFire/BurglarySystemsTo comply with UL 985 and 864 listing standards for fire alarm systems (effective March 1, 1989), the total combinedcontinuous and alarm current draw for the system during alarm conditions must be limited to 1.4 A (1400 mA) provided by the primary power supply (rectified AC). If current draw for the system exceeds 1.4 A, remove connected devices until the current draw falls below 1.4 A, then connect the removed devices to a D8132 Battery Charger Module or to an externalpower supply Minimum OperatingVoltage 10.2 VDC SDI Bus SDI Bus A (+): SDI Bus B (-): 9 VDC (15,000 ft. [4,572 m] max.) 9 VDC (15,000 ft. [4,572 m] max.)Telephone Connections ConnectionTwo TelCo Lines RJ31X or RJ38X jack can be interfaced with the panels. Radionics D928 Dual Phone Line Module required for two phone line service. Supervision supplied by the pane New FeaturesD7412GAccess Control: YES, 2 DoorsExpanded Users Arm/Disarm Passcodes: 99 Cards/Tokens: 396Passcode-ProtectedCustom Functions: 4Number of Printers: 1Number of Points: 75Number of Relays: 64 Alarm controls U1 Programmable timer- 1 Second to 62 Minute Timing Range Four Modes of Operation S.P.D.T. 3 Amp Relay Contacts Delay on Operation/Release Mode One Shot/Pulsing Mode Extreme Accuracy & RepeatabilityBosch D8129-Programmable relay functions Provides eight Form C relays 1 A at 30 VDC relay contact rating Slide switch configuration Shipping weight 20 LBS Allows remote control of relays The D8129 Octo-relay Module is suitable forapplications requiring Form C relays to operate auxiliary systems or to display fire system status at remote annunciators. Building components such as HVAC, door lock releases, and stairwell pressurization can interface with the D8129 for complete systemcontrol and monitoring. Industrial, commercial, and institutional facilities are typical installations for the D8129 module. The eight on-board relays can be programmed to activate on system alarm, system trouble, individual zone or point faults, and through remote control by authorized users. Bosch D8128D- .Power Requirements Voltage:12 VDC nominal Current: Standby (supervised): 25 mA maximum Alarm (all points shorted): 50 mA maximum Environmental Considerations Operating Temperature: +32°F to +120°F (0°C to +49°C) Relative Humidity:0% to 93% LoopEnd-of-Line (EOL) Resistance: 1 k?Wiring Resistance: 100? maximum Response Time: Approximately 1 sec. OctoPOPIT sensor loops are supervised with a 1 k?EOL resistor, D105BL or D105FL, for fire supervisory applications

Condition	Used : An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
Seller Notes	“Nothing is wrong with it. It is just an old panel that I do not use anymore. Not much wear on any of the items in the enclosure except the cardboard box that its in. It comes with resistors. See pictures for all that is included. If you want to buy one of the individual parts, just message me.”