Rain / Snow Sensor Controller Ds-2b

US $480

Jerusalem, Israel
Jun 23rd

Open on mobile:
QR code

Overview of the DS Series The ASE DS series of sensors and controllers provide a balance between price, sophistication, and control capabilities and capacities. Each unit is housed in a sturdy NEMA 3R enclosure rated for outdoor use. All internal electronic components are spec'ed for -40oC to +85oC operation. All line voltage units are ETL UL Standard 508/CSA C22.2 No. 14 Listed and European CE EMC directives have been achieved, opening the door for both domestic and overseas use. If you are tired of throwing old sensors away with no possibility of repair, take a look at the DS series. Unlike "potted" sensors and controllers, every DS unit offers full access to the sensor electronics. This unique design allows configuring and adjusting the unit for most efficient operation. The precipitation sensor may also be replaced in the field. Why replace the whole controller when an inexpensive precipitation sensor may restore your system to "like new" performance? Tired of stocking 10 different part numbers for the same basic sensor? At ASE, we exploit our microcontroller design to the fullest. Every line voltage DS unit can accept and control any input supply from 100VAC to 277VAC. And low voltage companions for the DS-2C (DS-224C) and DS-8C (DS-824C) are available for hydronic and other low voltage systems. All options and adjustments for each unit are field selectable. This allows covering all of your requirements while keeping your stock low and lead times short. Pigtail cable color codes conform to international standards and all units now ship with a 3/4" base conduit hub and a 3/4"-to-1/2" threaded reducing bushings. One sensor = one part number. Standardization means fewer variants, lower costs, and less inventory requirements for you. Basic Theory of Operation All DS units operate by detecting environmental conditions through a base mounted temperature sensor and a heated precipitation sensor. When rain or snow land on the precipitation sensor the traces are bridged and a closure is detected. The heater then rapidly evaporates the moisture, clearing the sensor. The sensor for the DS-2C, DS-224C, DS-4C, and DS-5C simply screws into the top of the controller enclosure. The DS-7C, DS-8C, DS-9C, and DS-824C precipitation sensors are connected to a 10 foot cable and are intended for remote mounting, either on a feed boom for satellite antenna deicing or in a gutter or downspout for roof deicing. These signals are then supplied to the microcontroller. Depending on the way the user has configured the sensor the microcontroller determines the appropriate action to perform. For example, the DS-4C contains two control relays. Using the profile selection switch (see the DS-4C page for more information) the controller can close one relay for low temperature detection and the other for precipitation detection. It can also be configured to close one relay when rain is detected and the other when snow is detected. It can also close both relays only when snow is detected, allowing control of larger loads. The difference between "sensor" and "controller" modes is the "Delay Off" drying cycle provided by each configuration. "Delay Off" time is the amount of time the sensor/controller will hold the load control relay(s) closed after the last detection of rain or snow. Proper setting of "Delay Off" assures that pavement or roofs not only melt but also dry, reducing the chance for dangerous refreezing of water left behind. A sensor is used to activate an external control unit when rain or snow is occurring. The external control unit activates and operates the deicing system as required. A controller is expected to not only detect snow or rain conditions but to also directly control the attached equipment. A DS series unit set as a controller provides a longer delay off time, typically 30-90 minutes or 2-6 hours, allowing the heating system to dry the surface and prevent refreezing. All DS units provide a remote "control/monitor" interface, a point where ASE or customer supplied devices can be connected to remotely monitor activation of the system and/or manually activate or disable the controller. Some units also feature a built-in switch to perform these same control functions directly from the sensor. The rack-mounted DP-7B or wall-mounted CDP-2 Remote Control/Status Panels may be directly connected to any DS series sensor/controller in order to provide both remote control and monitoring of DS sensor/controller operation. Common Features List: Reliable Rain and/or Snow Detection Can Also Function as a High Power Intelligent Thermostat Line Voltage Units: Supply - Universal 100-277V AC 50/60 Hz Operation, No Strapping Required Control - Full 30A @ 277V AC, 20A @ 28V DC Low Voltage Units: Supply - 22-28V AC/DC, 15VA Max Control - Full 30A @ 24V AC, 20A @ 28V DC Inexpensive, Replaceable Precipitation Sensor Easy Installation, Full Access to Electronics 10 Different Functions, 1 Part Number, Simplified Ordering Standard 3/4" NPT Conduit Hub, Includes 3/4" to 1/2" Reducer Adjustable Temperature Trigger Point Adjustable Delay Off Drying Timer with 30-90 Min or 2-6 Hr Ranges Adjustable Precipitation Sensitivity Super Bright Power/Activation LED Indicator Simple Remote Control/Monitor Capability Selectable Low Temperature Cutoff With Unique "Recover" Mode External Manual On-Automatic-Standby Override Switch (Except DS-4C/DS-7C) Smart "Manual On" Operates for One Delay Off Cycle